manualshive.com logo in svg

Dover PSG Mouvex P BI Series, Установка - Использование - Обслуживание, Страница: 35 / 45

Поделиться
Скачать
Dover PSG Mouvex P BI Series Скачать руководство пользователя страница 35

9.2 Remounting a single mechanical shaft seal

with grease container

• When fitting a shaft seal with grease reservoir, follow

steps 1 to 9 in § 

REPLACING A SINGLE MECHANI-

CAL SHAFT SEAL -

Reassembly

.

• Check and change seals as necessary 

646

(1) and 

647

(1). Be sure to fit the seal 

647

, with its lip facing the side

opposite the shaft exit.

• Slide the cover 

645

and seals 

646

and 

647

onto the

shaft 

501

, facing the lubricator thread 

644

downward

and the breather valve 

643

upward, then tighten the

screws 

729

and nuts slightly 

730

.

• Follow step 12 in § REPLACING A SINGLE MECHANICAL

SHAFT SEAL -

Reassembly

, then :

• Fit the lubricator 

644

and breather 

643

.

• Unscrew the 2 screws 

729

and push the cover 

645

out-

ward.

• Using a grease gun, fill the interior of the shaft seal hol-

der 

601

and the cover 

645

with grease, driving out as

much air as possible, then tighten the 2 screws 

729

.

• Use the lubricator to fill the reservoir with grease 

644

up

to the edge of the breather 

643

.

9.2.1  Filling the grease container 645 (on pumps

that have one)

Every 500 hours of operation : fill the grease container
up to the edge of the breather 

643

.

35/45

NT 1008-D00 08 18 P BI series  e

9. SHAFT SEAL (continued)

Содержание PSG Mouvex P BI Series














































Отзывы:

Нет отзывов