Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 136

background image

Issued May 2020
Maintenance and Adjustment

Copyright 2020, Heil Environmental

Printed in the U.S.A.

Maintenance and Adjustment

88

REPAIRING CRACKED WELD JOINTS

Repair all cracked weld joints immediately after finding cracked weld joints. If you are unsure of the proper repair
procedure, call Heil Technical Services at 866-310-4345.

OIL LUBRICANT RECOMMENDATION

Use only non-detergent engine oil to lubricate all moveable mechanical parts not furnished with grease fittings. Apply
sufficient oil to give good lubrication, but do not bathe parts in oil. Always wipe off excess.

GREASE LUBRICANT RECOMMENDATION

Use a grease gun. Before engaging grease gun, clean the fitting. Always pump enough grease to purge the joint of
contaminated grease and wipe off the excess. Lubricate a unit as given on the lubrication decal on the unit and in the Body
Lubrication Guide

paragraph of this section.

Use grade NLG1000 grease or equivalent.

TAILGATE LUBRICATION

See

Grease Lubrication Recommendation

and

Body Lubrication Guide

in this section.

INSPECT PROXIMITY SWITCHES

See

Proximity Switch Troubleshooting

for recommended procedures for inspecting proximity switches.

CLEAN AND INSPECT THE TAILGATE SEAL

Periodically check the tailgate seal to make sure it mates properly with the body and inspect for possible wear, damage or
leaking. Replace the seal as necessary. See the figure below.

Figure 33. Tailgate Seal

79

88

79

28

«
...
92
93
94
95
96
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: XTA Страницы: 29

Бренд: vc999 Страницы: 59

Бренд: Qtx Страницы: 3

Бренд: Saferoad Страницы: 24

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Dana Design Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды