background image

Lit. No. 76451/76452/76453, Rev. 04 

February 24, 2020

SAFETY

SAFETY PRECAUTIONS

Improper installation and operation could cause 
personal injury and/or equipment and property damage. 
Read and understand labels and the Owner's Manual 
before installing, operating, or making adjustments.

 WARNING

•  Driver to keep bystanders minimum of 

25 feet away from operating spreader.

•  Before working with the spreader, secure all 

loose-

fi

 tting clothing and unrestrained hair.

•  Before operating the spreader, verify that all 

safety guards are in place.

•  Before servicing the spreader, wait for 

conveyor, auger, and spinner to stop.

•  Do not climb into or ride on spreader.

 CAUTION

If rear directional, CHMSL light, or brake 
stoplights are obstructed by the spreader, the 
lights shall be relocated, or auxiliary directional 
or brake stoplights shall be installed.

 WARNING

 

   Overloading could result in an 

accident or damage. Do not 
exceed GVWR of UTV. See 
Loading section to determine 

maximum volumes of spreading material.

 CAUTION

Disconnect electric and/or hydraulic power 
and tag out if required before servicing or 
performing maintenance.

NOTE: Lubricate grease 

fi

 ttings after each use. 

Use a good quality multipurpose grease.

FUSES

The electrical system contains several automotive-style 
fuses. If a problem should occur and fuse replacement 
is necessary, the replacement fuse must be of the 
same type and amperage rating as the original. 
Installing a fuse with a higher rating can damage the 
system and could start a 

fi

 re.

 CAUTION

 

  DO NOT leave unused material in 

hopper. Material can freeze or solidify, 
causing unit to not work properly. 
Empty and clean after each use.

 CAUTION

•  Do not operate a spreader in need of 

maintenance.

•  Before operating the spreader, reassemble 

any parts or hardware removed for cleaning 
or adjusting.

•  Before operating the spreader, remove 

materials such as cleaning rags, brushes, 
and hand tools from the spreader.

•  Before operating the spreader, read the 

engine owner's manual, if so equipped.

•  While operating the spreader, use auxiliary 

warning lights, except when prohibited by law.

•  Tighten all fasteners according to the 

torque chart. Refer to torque chart for the 
recommended torque values.

 WARNING

Vehicles <10,000 lb GVWR: Obstructing the 
visibility from the vehicle's rear camera could 
result in serious injury or damage. An auxiliary 
camera system shall be installed if the 
vehicle's rear camera is removed or blocked.

Содержание SnowEx V-Pro SP-2000

















Отзывы: