Douglas Dynamics SnowEx Brine Pro 2000 Скачать руководство пользователя страница 10

TPS-200

Lit. No. 11814, Rev. 00 

10 

October 1, 2017

Copyright © 2017 Douglas Dynamics, LLC. All rights reserved. This material may not be reproduced or copied, in whole or in part, in 
any printed, mechanical, electronic, 

fi

 lm, or other distribution and storage media, without the written consent of TrynEx International, LLC. 

Authorization to photocopy items for internal or personal use by TrynEx International outlets or snowplow owner is granted.

TrynEx International reserves the right under its product improvement policy to change construction or design details and furnish equipment when 
so altered without reference to illustrations or speci

fi

 cations used. TrynEx International or the pump manufacturer may require or recommend 

optional equipment for brine making. TrynEx International offers a limited warranty for all brine makers and accessories. See separately 
printed page for this important information. The following are registered (

®

) or unregistered (™) trademarks of Douglas Dynamics, LLC: 

Brine Pro™, SnowEx

®

.

Printed in U.S.A.

Содержание SnowEx Brine Pro 2000











Отзывы: