manualshive.com logo in svg

Dosmatic SuperDos 45, Инструкция по установке и эксплуатации

Поделиться
Скачать
Dosmatic SuperDos 45 Скачать руководство пользователя страница 2

CONTENTS:  

CAUTION: 

To reduce risk of injury, user must read and understand the Installation & Operation Instructions 
before using this product.

ITEM PAGE
Introduction...........................................................................................................................................3
Safety.....................................................................................................................................................4
Installation..........................................................................................................................................5-7
Operation............................................................................................................................................8-9
Maintenance........................................................................................................................................10
Trouble Shooting.................................................................................................................................11
Repair Parts Motor..............................................................................................................................12
Specifications.......................................................................................................................................13
Repair Parts Lower Ends................................................................................................................14-19
Wear Parts Kits...............................................................................................................................20-22
Warranty.........................................................................................................................................23-24

START UP PROCEDURES

SLOWLY turn on main water pressure until water flows between 5 & 12 gpm (11-45 l/mn) or 30 psi 
(2 bar) maximum to fully prime the suction hose.
SLOWLY open the water supply valve and all valves downstream of injector to release entrapped 
air. Carefully open inlet valve allowing water to enter and pressurize the injector. Open outlet valve 
and close bypass valve. Water will now flow through the injector, and a continuous sound will be 
emitted from the injector as water passes through it. Check for system leaks (see page 5) and correct 
if necessary. Adjust the outlet valves downstream from the injector, if necessary.

IMPORTANT:

FOR WARRANTY PURPOSES

VISIT OUR

WEBSITE

WWW.DOSMATIC.COM

TO FILL OUT PRODUCT

REGISTRATION FORM!

Part#013827 Rev A

Содержание SuperDos 45
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды