Dormakaba BEST Wi-Q 45HQ Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 12

Dormakaba BEST Wi-Q 45HQ Скачать руководство пользователя страница 12

Installation Instructions for Wi-Q™ Technology 45HQ Mortise Locks

BEST

a Product Group of dormakaba USA Inc.

12

Testing the lock

©20

19

a Product Group of dormakaba USA Inc.

T82623/Rev

F

3108931 ER-7991-12

November

2019

20

Test lock

For 45HQ Locks with keypad

To test the lock for proper operation before the lock is
programmed, follow these instructions:

1 Press

1234

.

2 Press

#

.

The green light flashes and the locking mechanism
unlocks.

3 Turn the lever and open the door.

For all other locks:

To test the lock for proper operation before the lock is
programmed, use the temporary operator card that
came with the lock. This card is for temporary use only.
After permanent cards have been programmed for the
lock, the temporary card should be deleted.

1 Use the temporary operator card to activate the

lock.

Note:

If the lock has a proximity card reader, it may

have already been activated by the presence of an
object near the card reader.

2 Use the temporary operator card to access the lock.

The green light flashes and the locking mechanism
unlocks.

3 Turn the lever and open the door.

If the mechanism doesn’t unlock, refer to the following
table. For additional troubleshooting instructions, see
the

Service Manual

.

For all locks

1 Insert and turn the key to unlatch the door.

For all TV function locks

2 From the inside of the door, turn the turn knob and

make sure that the deadbolt operates properly.

LEDs

Sounder You should

Single

red flash

—

Red

flashes

3 short

tones

Green

flashes

—

—

—

Use the card at a moderate speed.

Use the temporary operator card
provided with the lock.

Check the motor connection.

Check the battery connection.

«
...
10
11
12

Содержание BEST Wi-Q 45HQ













Отзывы:

Нет отзывов