background image

 

 

Stand  08.02.2012 

 

Technische Änderungen vorbehalten 

Software-Update_Ver1010_GB.doc 

DORMA KT-Systeme

 

Seite 14 von 14

 

 

KTC-2 (MS9) 

 
 
If all changes are carried out, please put the door system back into operation as 
follows: 

 
 

10. Initial operation of the door system 

 

  The emergency-stop is activated 

  The control system is switched on 

  Program switch KT on Automatic 1 

  The curved sliding door wings and the showcase doors are closed 

  The frequency converter and the CPU are parameterized 

  Door system is in summer position 

  Push Select push button and keep it pushed for 4 sec 

 Release emergency-stop 

 Learning cycle starts 

 

Indication of learning cycle and positioning drive 

During the learning cycle and positioning drive the display shows a gyro. 
 

 

  Door system rotates in positioning speed 

  The door system turns for min. 1 rotation  

  Afterwards the door system restarts with its regular function 

  Check all functions according to the original manual and/or the attached chart. 

  Check if the control system has learned the correct diameter. Check via parameter 

.  

 
 
 

11. Testing of changes 
 

-  Door systems with UPS: Revolving door has to rotate in program switch position 

Auto1 or Auto2 into summer position and stop there. 

-  Program switch position in „Summer“ and the sliding door is in operation (test all 

program switch positions of the sliding door), sliding door must stop in case the 
emergency-stop is activated and remain in this position as long as this is 
activated. 

-  Check all revolving door functions again. 

 

 

Done 

 
 
 
 
 

Содержание KTC-2















Отзывы: