Dorex DX2 FW Скачать руководство пользователя страница 8

Страница: 8 / 16

11. INSTALL TOP LATCH AND ROD (CONTINUED)

12. CHECK TOP LATCH FOR HOLDBACK AND DEADLOCK

8 / 16

Top

Latch

Figure 3

Rod

Connecting

Screws

Rod

Connecting

Screw

Notch

Tab

Connecting

Bar

Second

Holes

Side

Screws

3. Attach the connecting Bar to the bottom of the top

rod with supplied screw (Figure 3)

Connecting

Bar

Connecting

Bar

NOTE:

Match notch of the connect-

ing link with tab of rod before

tighten connecting screw

4. Assemble rod guide with rod, thread rod into top latch until first

hole in connecting bar align with first hole in retractor and

fasten with side screws.

Rod

Guide

First Holes

Open

Adjustment Screw

1. Pushing on push bar will retract the latchbolt and

allow the door to open. Latchbolt will stay

retracted, if not adjust the screw on top of the

retractor with a screw driver.

2. Once the door is closed the strike will engage with the deadlock, which

will allow the latchbolt to engage inside the strike. The latchbolt cannot

be retracted when the door is closed. If not, adjust the strike position to

engage with the device deadlock.

Содержание DX2 FW

















Результаты поиска

Содержание DX2 FW

Отзывы:

Похожие инструкции для DX2 FW

Бренды по названию

Популярные бренды

Dorex DX2 FW, Руководство по установке

Результаты поиска

Содержание DX2 FW

Отзывы:

Похожие инструкции для DX2 FW

Бренды по названию

Популярные бренды