Doosan LIGHTSOURCE V9, Руководство по эксплуатации и обслуживанию

Страница: 15 / 66

SAFETY
11
LIGHTSOURCE V9
Close and lock all access doors when the generator set is left
unattended.
Do not use extinguishers intended for Class A or Class B fires on
electrical fires. Use only extinguishers suitable for class BC or class
ABC fires.
Keep the towing vehicle or equipment carrier, generator set,
connecting cables, tools and all personnel at least 3 metres from all
power lines and buried power cables, other than those connected to the
generator set.
Attempt repairs only in clean, dry, well lighted and ventilated areas.
Connect the generator set only to loads and/or electrical systems
that are compatible with its electrical characteristics and that are within
it’s rated capacity.
Transport
When loading or transporting machines ensure that the specified
lifting and tie down points are used.
When loading or transporting machines ensure that the towing
vehicle, its size, weight, towing hitch and electrical supply are all
suitable to provide safe and stable towing at speeds either, up to the
legal maximum for the country in which it is being towed or, as specified
for the machine model if lower than the legal maximum.
Ensure that the maximum trailer weight does not exceed the
maximum gross weight of the machine (by limiting the equipment load),
limited by the capacity of the running gear.
Note:
Gross mass (on data plate) is for the basic machine and fuel only,
excluding any fitted options, tools, equipment and foreign materials.
Before towing the machine, ensure that: −
. the tyres and towing hitch are in a serviceable condition.
. the canopy is secure.
. all ancillary equipment is stored in a safe and secure manner.
. the brakes and lights are functioning correctly and meet necessary
road traffic requirements.
. break-away cables/safety chains are connected to the towing
vehicle.
The machine must be towed in a level attitude (the maximum
permissible drawbar angle is between 0 and +5 from horizontal) in
order to maintain correct handling, braking and lighting functions. This
can be achieved by correct selection and adjustment of the vehicle
towing hitch and, on variable height running gear, adjustment of the
drawbar.
To ensure full braking efficiency, the front (towing eye) section must
always be set level.
When adjusting variable height running gear: −
Ensure front (towing eye) section is set level
When raising towing eye, set rear joint first, then front joint.
When lowering towing eye, set front joint first, then rear joint.
After setting, fully tighten each joint by hand and then tighten further
to the next pin. Refit the pin.
When parking always use the handbrake and, if necessary, suitable
wheel chocks.
Make sure wheels, tyres and tow bar connectors are in safe
operating condition and tow bar is properly connected before towing.
Do not store or transport hazardous or combustible materials in or
on this unit.
Do not suspend this machine with other equipment hanging from the
running gear.
Safety chains / connections and their adjustment
The legal requirements for the joint operation of the breakaway
cable and safety chains are as yet unidentified by 71/320/EEC or UK
regulations. Consequently we offer the following advice / instructions.
Where brakes only are fitted:
a) Ensure that the breakaway cable is securely coupled to the
handbrake lever and also to a substantial point on the towing vehicle.
b) Ensure that the effective cable length is as short as possible, whilst
still allowing enough slackness for the trailer to articulate without the
handbrake being applied.
Where brakes and safety chains are fitted:
a) Loop the chains onto the towing vehicle using the towing vehicle
hitch as an anchorage point, or any other point of similar strength.
b) Ensure that the effective chain length is as short as possible whilst
still allowing normal articulation of the trailer and effective operation of
the breakaway cable.
Where safety chains only are fitted:
a) Loop the chains onto the towing vehicle using the towing vehicle
hitch as an anchorage point, or any other point of similar strength.
b) When adjusting the safety chains there should be sufficient free
length in the chains to allow normal articulation, whilst also being short
enough to prevent the towbar from touching the ground in the event of
an accidental separation of the towing vehicle from the trailer.
Before towing
Make sure wheels, tires and tow bar connectors are in safe
operating condition and tow bar is properly connected before towing.