background image

Installation, Operation and Maintenance manual

40

Downflo

®

 Evolution

Diaphragm valve

Valve disassembly
Disassemble in an orderly fashion. Pay careful attention to exploded views provided 

for identification of parts.
1.  Remove the clipring from the valve body to remove the bonnet. Use a screwdriver 

on 3 places at the bonnet, start removing the clipring on the inlet side. Then 

remove the piston/diaphragm assembly.

2.  Remove pipes if necessary and in that case remove the pipe o-rings from the 

body with a suitable device.

3.  All parts are now accessible for cleaning or replacement.
Valve reassembly
Reassemble in reverse order of disassembly paying careful attention to exploded 

views provided for identification and placement of parts.

  Lubricate all gaskets and o-rings with high quality silicone grease.

1.  Replace piston/diaphragm-assembly.

  Locate bleedhole in piston/diaphragm opposite to the valve inlet for the 

best performance.

2.  Replace the clipring on the body, with the open end towards the inlet side of 

the body. The legs of the clipring should point outwards from the valve and they 

should be evenly spaced from the stop in the groove.

3.  Replace the bonnet by pressing it firmly against the piston/diaphragm. Use pliers 

to press the ends of the clipring together.

4.  Replace pipe o-rings, then slip the clamp o-rings over the inlet pipe. Replace 

the valve on the pipe and move the clamp o-ring over the pipe against the valve 

body. Replace the clamps and torque the clamp screws according to torque chart 

(16 Nm ± 2Nm). The clamp o-ring is necessary to fixate the valve in place.

5.  After maintenance, operate the valve a few times to be sure of proper operation.

Содержание Downflo Evolution DFE 2-12















































Отзывы: