background image

Installation, Operation and Maintenance manual

24

DFPRE 4 Dust Collectors

TABLE 1 – FAULT LOCATION (CONTINUED)

Symptom

Possible cause

Action

Total loss of 

suction.

Fan motor stopped.

Check motor supply overloads, fuses and interlocks (if fitted).

Check motor connections and windings.

Unit blocked.

Check that dust container is not overfull. Check starter overloads, 

fuses and interlocks.

Run unit clear*, then remove each cartridge in turn and renew any 

that are damaged.

Ducting blocked.

Check throughout and clear.

Visible effluent in 

clean air outlet.

Filter cartridges not 

properly sealed.

Check cartridge access covers are seated and seal properly.

Damaged filter cartridge. Damaged cartridges can be identified by the dust present in clean 

air chamber. Withdraw cartridge and renew. 

Dust container 

pressure balance 

(if fitted) not 

working.

Leaking balance pipe 

connection.

Check connections and rectify.

Excessive noise 

from diaphragm 

valve.

Diaphragm valve failure.

Check for debris, obstruction, valve wear or diaphragm failure. 

Replace damaged valve or parts.

*To run unit clear, switch off main fan only and allow the controller to perform several complete 

cleaning cycles before switching off compressor etc.

Содержание DFPRE 4 Series




























Отзывы: