DOMUSA TEKNIK SIRENA CAL HFD Скачать руководство пользователя

Страница: 7 / 32

INSTALLATION WATER-FILLING

In order to fill the installation, open the filling valve up to the pressure gauge

(5)

indicates a pressure

between 1 and 1.5 bar. Filling is to be carried out slowly and with the automatic air vent open, so that

the installation air will be released. In addition, the other parts of the installation are to be properly

drained by means of the air vent valves fitted for such a purpose. Once the installation has been filled

up, close the filling valve.

NOTE: Switching on the boiler without water could result in serious damage to it.

SAFETY LOCKING

The boiler is provided with two types of operating safety locking:

5.1

Temperature safety locking

This locking is indicated by the temperature locked out neon light

(9)

. It will occur every time the

temperature in the boiler exceeds 110º C. The safety thermostat

(1)

built-in button will be pressed

in order to unlock it, once the plug covering this button has been previously loosened.

5.2

Burner locking

This locking is indicated by the burner locked out neon light

(10)

. It is caused by any failure which

could exist in the burner or oil line. To unlock, press the burner lighted push button which becomes

put on

(16)

NOTE: If any of these lockings were repetitive, contact the nearest authorised Technical Assistance.

BOILER OPERATION

Select the temperature desired in the control thermostat

(2)

and in the room thermostat (if any).

Switch on the boiler setting the main selector

(6)

to "I" position and to "



" position. The burner will

start operating up to the boiler reaches the temperature selected on the control thermostat (it

should be between 60 ºC and 85 ºC). In its turn, the circulating pump will start operating. When the

room temperature is higher than or equal to that rated on the installation room thermostat (if any),

the circulating pump will stop

6.1

Boiler operation with a Sanit hot water tank

The model Sirena Cal HFD can be supplied with a Sanit DHW tank of DOMUSA TEKNIK to install

them in combination, to obtain a high production of DHW. For a correct installation of the tank

follow carefully the installation and operating instructions included with the tank.

The boilers are supplied with an optional heating outlet IC' (see Dimensions) to connect the DHW

tank Sanit to the boiler. To work with the combination of the boiler and Sanit DHW tank, the boiler's

main selector has two different positions, Summer and Winter:

- Summer position

☼

: The boiler will supply, at this position, only DHW, putting on the burner

and the DHW circulating pump (summer pump) up to the tank reaches the temperature

selected on the DHW regulation thermostat, placed on the main board of the tank. When the

temperature selected in the DHW tank is reached, the burner and the summer pump will stop.

- Winter position



: The boiler will be, at this position, capable of heating the DHW tank and

heating installation, giving priority to the DHW production.

Содержание SIRENA CAL HFD

































Результаты поиска

Содержание SIRENA CAL HFD

Отзывы:

Похожие инструкции для SIRENA CAL HFD

Бренды по названию

Популярные бренды

DOMUSA TEKNIK SIRENA CAL HFD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SIRENA CAL HFD

Отзывы:

Похожие инструкции для SIRENA CAL HFD

Бренды по названию

Популярные бренды