Dometic Pico FTC 1X1, Инструкция по установке и эксплуатации

Страница: 11 / 16

EN
4445103664 11
Pico FTC 2X2/1X1
Intended use
This tent is suitable for:
• Light to moderate weather
• Touring
This tent is not suitable for:
• Very strong winds or snowfall
• Seasonal pitch or commercial use
This product is only suitable for the intended purpose and application in
accordance with these instructions.
This manual provides information that is necessary for proper installation
and/or operation of the product. Poor installation and/or improper oper-
ating or maintenance will result in unsatisfactory performance and a possi-
ble failure.
The manufacturer accepts no liability for any injury or damage to the prod-
uct resulting from:
• Incorrect assembly or connection, including excess voltage
• Incorrect maintenance or use of spare parts other than original spare
parts provided by the manufacturer
• Alterations to the product without express permission from the manu-
facturer
• Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product
specifications.
Using the tent
!
Before first use
Familiarize yourself with the product by carrying out a test set up before
the product is used for the first time. Check if the scope of delivery is
complete.
Santorini, Pico only: Weathering your product before first use
The product is manufactured with materials that require preparation
before use to maximize its weatherproofing.
1. Fully set up the product outside when rain is expected or where you
can hose the outside of the product to become thoroughly wet.
This process is known as weathering. The weathering process tight-
ens the fabric, and allows the cotton in the sewing thread to swell and
fill the holes made by the sewing needle during the manufacturing
process.
2. Allow the product to dry thoroughly before packing away.
By following this process before first use, will ensure that the product
weatherproofing will improve with subsequent soakings.
Choosing a site
Choose a flat site that is protected from wind:
1. If necessary, use a windbreak.
2. Choose a shaded site to avoid UV degradation of the fabric.
3. Avoid pitching under trees as falling branches, resin, etc. can damage
the product.
4. Clear the site of sharp stones and debris to avoid damaging the
groundsheet.
5. Set up the product with the doors facing away from the wind.
Setting up the tent
!
A
I
Keep the following tips in mind while setting up the tent:
• The figures provide a general overview of the set-up. The actual set-up
will vary slightly based on the model of tent.
• Get help. The set-up is easier with more people.
• Inflate the air poles from front to rear.
• After standing the tent upright, check the corner pegs and re-peg if
necessary. The groundsheet on the inside should be taut and in a
rectangular shape.
• Peg the guy lines so that the tent is under tension without distorting
the shape.
• If available, attach the storm straps.
• Check the guy lines from time to time to ensure adequate tension, if
necessary use the runners to adjust.
Set up the tent as follows:
1. To protect the tent from dirt and damage, lay down a groundsheet or
footprint before unpacking.
2. Unpack the tent.
3. Separate and identify the different components.
4. Proceed as shown to set up the tent:
– Santorini: fig.
2
, page 4 to fig.
9
, page 5.
– Reunion: fig.
0
, page 5 t o fig.
j
, page 7.
– Pico: fig.
k
, page 7 to fig.
r
, page 8.
Removing the flysheet (Reunion only)
➤
Proceed as shown to remove the flysheet: fig.
i
, page 7.
➤
Attach the flysheet before dismantling the tent.
Dismantling the tent
A
1. Remove any dirt on the outside.
2. Close all window blinds or remove curtains.
3. Close all doors and openings.
Description Ref. no.
2X2 footprint 9120002114
1X1 footprint 9120002117
CAUTION! Risk of injury and material damage
Never open the zipper on the protective sleeve while an air
pole is inflated. This will result in the air pole bursting.
CAUTION! Risk of injury and material damage
• Do not use any type of compressor designed to inflate
car tires.
• Only inflate the mattress (if available) to a maximum of
2 psi/0.14 bar.
• Only inflate the air poles into the green zone of the
pressure gauge of the supplied hand pump
(10 psi/0.69 bar).
NOTICE! Material damage
Do not open or close the zippers by force.
NOTE
• The tent comes with general purpose pegs. These will
be suitable for many sites but for some types of ground
special pegs will be needed. Ask your dealer.
• Drive the pegs at a 45° angle away from the tent into the
ground.
• Peg the guy lines in line with the seam it starts from.
NOTICE! Material damage
Do not use force when dismantling the tent. Otherwise you
might damage any material.