Dometic EnviroComfort ECD Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

Dometic EnviroComfort ECD Скачать руководство пользователя страница 4

Unpacking and Inspection

EnviroComfort Installation Manual

2

L-2657 ENGLISH

K

IT

C

ONTENTS

EnviroComfort is a complete marine air conditioning kit that includes everything needed for a professional installation. Each kit
includes:

•

Air conditioning unit with electrical box

•

Dometic Digital Display temperature-control device

•

Ducting

•

Supply-air grille

•

Return-air grille

•

Seawater pump

•

Strainer

•

Speed scoop thru-hull

•

Overboard fitting

•

Seawater hose

•

Fittings for pump and strainer

T

OOLS

R

EQUIRED

FOR

I

NSTALLATION

•

Screwdrivers - both types

•

Pliers

•

Pipe wrench

•

Wire cutters/crimpers

•

Drill & 7/8" bit

•

Power screwdriver

•

Jig saw

•

Hull saw

•

Duct tape

•

Electrical tape

•

Teflon tape

•

Marine-grade waterproof (below waterline) bedding compound to seal thru-hull fittings

•

Hardware to secure unit, pump, strainer, grilles, electrical box and control panel

U

NPACKING

AND

I

NSPECTION

Before attempting to install your new air conditioning system, you must read this installation manual completely.

Failure to perform certain tasks in the proper sequence could result in an inoperative system as well as a voided warranty.

If, upon opening your new system, you discover any parts are missing, contact your dealer immediately. Check all items
carefully against the packing list to ensure all cartons have been received. Move units in the normal “up” orientation as indicated
by the arrows on each carton. Examine cartons for shipping damage, removing the units from the cartons if necessary. If the unit
is damaged, the carrier should make the proper notation on the delivery receipt acknowledging the damage.

«
...
2
3
4
5
6
...
»

Содержание EnviroComfort ECD

























Отзывы:

Нет отзывов