background image

3

A&E CATALINA 2500

Note: 

Make sure lock in top of awning arm assembly clears

top of case lip (FIG. 4C).  This is necessary for awning to

open properly.

Tighten lock knob.  Repeat steps 4B & 4C for other

side.

C. Using wand, hook pull-strap and pull awning out

about 3 feet (1 meter) (FIG. 4D).

D. While securely holding the pull-strap, tighten the lock

knobs on the rafter arms (FIG. 4E).

5. Snap awning foot into bottom mounting bracket (FIG.5).
6. Select a location for mounting of bottom mounting

bracket on side of vehicle.  The minimum mounting

distance from the bottom of the awning case to the

bottom of the bottom mounting bracket for the 2.5 meter

awning is 48”.  For the 3.0, 3.5 and 4.0 meter awnings it

is 58” (FIG. 6).

Note: 

Positioning of left and right bottom mounting brack-

ets should be at same level and centered to the awning

arms (FIG. 6).
7. Loosen lock knob and extend arm assembly keeping

arm perpendicular to awning case.  Once location is

determined, tighten lock knob (FIG. 7).

Note: 

The bottom mounting brackets should be mounted to

the floorline of solid structural member whenever possible.
8. Using the foot and bottom mounting bracket as a

template, drill a 1/8” dia. hole for the bottom screw.

Secure bottom mounting bracket with foot attached to

vehicle using a #10 x 1-1/2” long Phillips pan head

sheet metal screw thorough the foot and the bottom

mounting bracket.  Use a small dab of silicone sealant

on screw (FIG. 8)

9. A. Release foot from bottom mounting bracket and drill

a 1/8” dia. hole for the top screw.  Using a #10 x 1” long

Phillips pan head sheet metal screw with a dab of

silicone sealant on it, secure the top of the bottom

mounting bracket to vehicle (FIG. 9A).
Repeat Steps 5 thorough 9A for other side.

Note: 

For curved sided vehicles proceed to Step 9B.  For

straight sided vehicles skip to Step 10.

B. Loosen lock knob and lower arm assembly to

ground.  With foot still on ground raise inner arm as

high as it will go (FIG. 9B).

Note: 

Make sure lock in top of awning arm assembly clears

top of case lip (FIG. 9C).

Содержание Catalina 2500









Отзывы: