background image

1

USA
SERVICE OFFICE
Dometic Corporation
509 South Poplar Street
Lagrange, IN 46761
260-463-4858

CANADA
Dometic Distribution
866 Langs Drive
Cambridge, Ontario
CANADA N3H 2N7
519-653-4390

For Service Center
Assistance Call:
800-544-4881

SERVICE INSTRUCTIONS

REVISION
Form No.3105903.060  8/04
(Replaces 3105903.052)
(French 3108577.044)
©2004 Dometic Corporation
LaGrange, IN 46761

This manual must be read and un-
derstood before installation, ad-
justment, service, or maintenance
is performed. This unit must be in-
stalled by a qualified service tech-
nician. Modification of this product
can be extremely hazardous and
could result in personal injury or
property damage.

Lire et comprendre ce manuel avant de
procéder à l'installation, à des réglages,
de l'entretien ou des réparations.
L'installation de cet appareil doit être
effectuée par un réparateur qualifié.
Toute modification de cet appareil peut
être extrêmement dangereuse et
entraîner des blessures ou dommages
matériels.

REPLACEMENT INSTRUCTIONS FOR

828XXXX, 830XXXX, 833XXXX,

834XXXX, 836XXXX SERIES

MODEL 8300 AND SUNCHASER AWNINGS

 FABRIC        

 ROLLER TUBE        

 TORSION ASSEMBLY

MODELS

828(XXXX)

834(XXXX)

830(XXXX)

836(XXXX)

833(XXXX)

“More information https://www.caravansplus.com.au"

Содержание A&E Systems 828 Series










Отзывы: