Dometic 3311931.000-20 Скачать руководство пользователя страница 7

Страница: 7 / 17

INSTALLATION INSTRUCTIONS

FIG. 5

Duct Size And Requirements For 3105007.XXX And 3105935.XXX RAG

Register Required

Registers

8 Min - 12 Max.

(Per Unit)

14 Sq. In. Free

Area Per Register

D. Wiring Requirements

1. Route a copper, with ground, 120 Vac supply

wire from the time delay fuse or circuit breaker

box to the roof opening. Use a listed/certified

non metallic - sheathed single strand cable. See

"A. Table - Unit Data" on page (4).

a. This supply wire must be located in the front

portion of the roof opening.

b. The power

MUST

be on an appropriately

sized separate time delay fuse or circuit

breaker. See "A. Table - Unit Data" on page

(4).

Make sure that at least 15″ of supply wire

extends into the roof opening This ensures

an easy connection at the junction box.

d. Protect the wire where it passes into the

opening with approved method.

2. Route a dedicated 12 Vdc supply wire (18-22

AWG) from the RV converter (filtered side) or

battery to the roof opening.



When a Comfort Control Center 2 (here-

in-after referred to as CCC 2) thermostat

is being installed with more than 2 zones,

route a dedicated 12 Vdc supply wire (18-

22 AGW) to zone 1 and zone 3 roof open-

ing.

a. This supply wire must be located in the front

portion of the roof opening.

Make sure that at least 15″ of supply wire

extends into the roof opening.

3. Thermostat Communication Cable

a. CCC 2 Thermostat

I. Route a 4 conductor communication ca-

ble from the roof opening to the thermo-

stat mounting location using the shortest

most direct route. Make sure that at least

15″ of the wire extends into the roof open

ing and 6″ extends from the wall at the

thermostat mounting location. See "E.

Choosing Thermostat Location" on page

(8).



When more than one unit is being

installed (additional zones) with the

CCC 2 thermostat, an additional

4 conductor communication cable

MUST

be routed to each additional

unit roof opening. Make sure that

at least 15″ of the wire extends into

the roof opening. See (FIG. 27).

b. LCD SZ Thermostat

I. Route a 3 conductor communication ca-

ble, 18 to 22 AWG, from the roof open-

ing to the Liquid Crystal Display Single

Zone (hereinafter referred to a LCD SZ)

thermostat mounting location. Make sure

that at least 15″ of the wire extends into

the roof opening and 6″ extends from the

wall at the thermostat mounting location.

See "E. Choosing Thermostat Location"

on page (8).

Содержание 3311931.000-20


















Результаты поиска

Содержание 3311931.000-20

Отзывы:

Бренды по названию

Популярные бренды

Dometic 3311931.000-20, Руководство по установке

Результаты поиска

Содержание 3311931.000-20

Отзывы:

Бренды по названию

Популярные бренды