manualshive.com logo in svg

Dome DMWS1, Руководство пользователя, Страница: 15 / 18

Поделиться
Скачать
Dome DMWS1 Скачать руководство пользователя страница 15

Page 15

Leak Sensor Advanced User Manual

Configuration Parameters

Configuration Parameters

Configuration parameters are sent using a standard syntax to ensure interopera-

bility between all manufacturers’ products.  All values are represented using the 

hexadecimal number system.  
Typical syntax is as shown below. Note that the value sent must be the exact size, 

in bytes, as accepted by the setting.  The “extra” spaces should be filled with zeros 

(see the “value” column below.) 
Example Configuration Parameter: 

02 02 00 0A

Param #

Size

Value

02 

(Param #2)

02 

(2 Bytes)

00 0A 

(10)

Param 

#

Size

Name

Available Values

Default 

Value

05

This parameter enables or disables the audible alarm (“beeping”) functionality of the Leak Sensor.

01

Enable/Disable Audible Alarm

00

 (Audible Alarm Disabled)

01 

(Audible Alarm Enabled)

01 

(Audible 

Alarm 

Enabled)

06

This parameter enables or disables the Leak Sensor - if disabled, the device will not respond in any way to detected 

leaks.

01

Enable/Disable Water Detection

00

 (Water Detection Disabled)

01 

(Water Detection Enabled)

01 

(Water 

Detection 

Enabled)

07

This parameter defines the value sent by the BASIC_SET command to Association Group 2 (for more information, 

see “Assocation Groups”.)

01

Basic Set Level

00

 (0/Turn Off Device)

01 ~ 63 

(0-99)

FF 

(255/Turn On Device)

FF 

(255/Turn 

On Device)

Table 6 - 

Configuration Parameters

Содержание DMWS1



















Отзывы:

Нет отзывов