Dome DMDP1 Скачать руководство пользователя страница 18

Страница: 18 / 20

Page 18

Door/Window Sensor Advanced User Manual

“Configuration” Command Class Parameters

Table 9 -

Door/Window Sensor Configuration Parameters

Param

Size

Name

Available Values

Default

Value

The Door/Window Sensor can report temperature values in either Celsius or Fahrenheit, and

this parameter allows the user to decide which unit is used.

Temperature Units

(Temperature is Reported in Fahrenheit)

(Temperature is Reported in Celsius)

(Temperature

is Reported in

Fahrenheit)

This parameter sets the value sent by the Basic Set command to Association Group 2. The

Door/Window Sensor sends a Basic Set command to Association Group 2 both when the tamper

switch opens and closes (for more information, see “Group 2” on page 14.)

Basic Set Value (Group 2)

(0/Turn Off Device)

01 ~ 63

(0-99)

(255/Turn On Device)

(255/Turn On

Device)

This parameter sets the value sent by the Basic Set command to Association Group 4. The

Door/Window Sensor sends a Basic Set command to Association Group 4 when the door or window

opens (for more information, see “Group 4” on page 14.)

Basic Set Level (Group 4 Opening)

(0/Turn Off Device)

01 ~ 63

(0-99)

(255/Turn On Device)

(255/Turn On

Device)

This parameter sets the value sent by the Basic Set command to Association Group 4. The

Door/Window Sensor sends a Basic Set command to Association Group 4 when the door or window

closes (for more information, see “Group 4” on page 14.)

Basic Set Level (Group 4 Closing)

(0/Turn Off Device)

01 ~ 63

(0-99)

(255/Turn On Device)

(0/Turn Off

Device)

Содержание DMDP1





















Результаты поиска

Содержание DMDP1

Отзывы:

Бренды по названию

Популярные бренды

Dome DMDP1, Руководство пользователя

Результаты поиска

Содержание DMDP1

Отзывы:

Бренды по названию

Популярные бренды