domat THERMASGARD HTF 200, Инструкции по эксплуатации, монтажу и установке

Страница: 8 / 12

G
THERMASGARD ® HTF
Rev. 2020 - V16
1x two-wire connection
standard
1x two-wire connection
LM 235 Z (KP 10)
1x four-wire connection
(optional)
THERMASGARD
®
HTF – Sleeve sensor ⁄ cable temperature sensor
Type ⁄ WG03
– Sensor ⁄ Output
Measuring ranges
PVC Silicone PTFE glass fibre
(IP 65) * (IP 65) * (IP 65) * (IP 54)
HTF 50
(NL = 50 mm)
HTF 50 Pt100, class B
– 35...+105 °C – 50...+180 °C – 50...+250 °C – 50...+350 °C
HTF 50 Pt1000, class B
– 35...+105 °C – 50...+180 °C – 50...+250 °C – 50...+350 °C
HTF50 Pt1000 A, class A-TGA
– 35...+105 °C – 50...+180 °C
HTF 50 Ni1000
– 35...+105 °C – 50...+180 °C – –
HTF 50 Ni1000 TK5000,
LG – Ni1000 – 35...+105 °C
–50
...
+150 °C
– –
HTF 50 NTC 1,8 K, 5K, 10K, 20K, 30K, 10K Precon
– 35...+105 °C
–50
...
+150 °C
– –
HTF 50 KTY 81-210, 81-110, 81-121, 81-122, 11-6
– 35...+105 °C
–40
...
+125 °C
– –
HTF 50 LM235Z
(TCR = 10 mV ⁄ K, 2.73 V at 0 °C), KP10 – 35...+105 °C
–40
...
+125 °C
– –
HTF 200
(NL = 200 mm)
HTF 200 Pt100
– 35...+105 °C – 50...+180 °C – –
HTF 200 Pt1000
– 35...+105 °C – 50...+180 °C – –
HTF 200 Ni1000
– 35...+105 °C – 50...+180 °C – –
HTF 200 Ni1000 TK5000,
LG – Ni1000 – 35...+105 °C
–50
...
+150 °C
– –
HTF 200 NTC 1,8 K, 5K, 10K, 20K, 30K, 10K Precon
– 35...+105 °C
–50
...
+150 °C
– –
HTF 200 KTY 81-210, 81-110, 81-121, 81-122, 11-6
– 35...+105 °C
–40
...
+125 °C
– –
HTF 200 LM235Z
(TCR = 10 mV ⁄ K, 2.73 V at 0 °C), KP10 – 35...+105 °C
–40
...
+125 °C
– –
The sleeve sensor ⁄ cable sensor THERMASGARD
®
HTF is used to measure temperatures in liquid and
gaseous media. It can be used as a duct sensor and - if installed in an immersion sleeve - as an immersion
and screw-in sensor. The sleeve length varies, depending on request, from 30...400 mm (standard is 50 mm
respectively 200 mm), the cable length is arbitrary (standard is 1.5 m). Depending on application, with
silicone, glass fibre, or PVC leads, for two-wire or four-wire connection. For direct, continuous use in liquids,
please use our THE immersion sleeves.
TECHNICAL DATA
Measuring ranges: –35...+105 °C PVC , LiYY, 2 x 0.25 mm²
–50...+180 °C Silicone , SiHF, 2 x 0.25 mm²
–50...+250 °C PTFE , 2 x 1.0 mm²
–50...+350 °C glass fibre , 2 x 0.25 mm²
ends stripped with wire end sleeves (extended measuring range
limits optional, depending on connection leads,
T
max
Ni1000 =
+180 °C
,
T
max
NTC / Ni1000 TK5000 = +150 °C ,
T
max
LM235Z = +125 °C )
Sensors ⁄ output: see table, passive (optional also with 2 sensors)
( Perfect Sensor Protection with IP68)
Connection type: 2-wire connection (4-wire connection optional)
Testing current:
< 0.6 mA (Pt1000)
< 1.0 mA (Pt100)
< 0.3 mA (Ni1000, Ni1000 TK5000)
< 2.0 mW (NTC xx)
400 μA...5 mA (LM235Z)
Protective tube stainless steel,
V4A
(1.4571), Ø = 6 mm
(sensor sleeve): nominal length (NL) HTF 50 = 50 mm / HTF 200 = 200 mm
(other optional dimensions also available,
nominal length (NL) = 30...400 mm)
cable entry stamped (optional rolled)
Connection cable: cable length (KL) = 1.5 m (optional also 3 m, 5 m, 8 m, 10 m)
Insulating resistance: ≥ 100 MΩ, at +20 °C (500 V DC)
Process connection: using immersion sleeves THE or
mounting flange, plastic (optionally in galvanised steel)
Permitted humidity: < 95 % r.H., non-precipitating air
Protection class: III (according to EN 60 730)
Protection type: IP 65 (according to EN 60 529) humidity-tight stamped
IP 68 (optional watertight compound-filled * ) rolled
IP 54 (optional glass fibre cable)
ACCESSORIES
MF - 06 - K
Mounting flange, plastic, 56.8 x 84.3 mm, Ø = 6.2 mm tube gland, T
max
= +100 °C
(is not included in scope of delivery)
THE - ms ⁄ xx Immersion sleeve, brass, nickel-plated,
Ø = 9 mm, inserted length (EL) = 50 - 250 mm, inner diameter of socket Ø = 5.2 mm,
with adjusting screw M12 x1.5, T
max
= +130 °C, p
max
= 16 bar
THE - VA ⁄ xx Immersion sleeve, stainless steel, V4A (1.4571),
Ø = 9 mm, inserted length (EL) = 50 - 400 mm, inner diameter of socket Ø = 5.2 mm,
with adjusting screw M12 x1.5, T
max
= +200 °C, p
max
= 40 bar