Dolmar FH-2500, Оригинальное руководство пользователя

Страница: 8 / 20

8
Only use original Dolmar replacement parts and ac-
cessories intended for your machine. Otherwise it may
result in personal injury or damage on the machine.
Store the machine in a dry room. Keep it out of reach of
children. Never store the machine outdoors.
ASSEMBLY
CAUTION:
Always be sure that the machine is switched off and
unplugged before carrying out any work on the tool.
1. Place the upper enclosure upside down on the flat
floor. And then put the base frame on it. Be careful
about the direction of the part. (Fig. 2)
. Fasten each part by tightening screws. Make sure they
become perfectly stable. (Fig. 3)
. Attach the stoppers by screw. Make sure they are
fastened tightly. (Fig. 4)
. Attach wheels as follows: (Fig. 5)
Attach the axis on one of the wheel.
Pass the axis through the holes on the leg.
Attach the other wheel to the axis by passing
the pin through the hole on the axis. Fasten the
wheel by bending the pin.
Attach the covers on the wheels.
. Attach the retaining basket. And then raise the lock
lever. (Fig. 6)
FUNCTIONAL DESCRIPTION
WARNING:
Before plugging the machine, always make sure that the
machine is switched off. Plugging the machine with the
switch on may cause an unexpected start resulting in
serious personal injury.
Power Switch (Fig. 7)
CAUTION:
Do not use the machine if the switch does not turn it on
and off. Have defective switches replaced by Dolmar
authorized service center.
To turn on the machine, push the green button.
To turn off the machine, push the red button.
LED light
The LED light indicates the status of the machine as
follows:
RED color: When the machine is connected to the
power supply and the machine is switched off.
GREEN color: When machine is switched on.
Flickering GREEN color constantly: When the
machine is blocked during operation.
Flickering RED color: When the machine can not
recover automatically. Clear the problem manually
when it happens.
Unintentional restart proof
The machine switches off automatically when power
failure happens. To restart, push the green button again.
•
•
•
–
–
–
–
Overload protection
The motor is equipped with an overload protection. When
overloaded, the machine acts as follows:
The blade runs reverse for two or three seconds
to try to push the shredded material back out.
The blade runs forward again.
If the material is still clogged after this attempt
for three times, the machine stops with LED light
flickering in red.
When it happens perform the following steps:
Turn off the machine.
Wait until the blades stop completely.
Remove the clogged material.
Turn the shredder on again after about minutes,
and feed easier material.
If you cannot turn on the machine after this wait-
ing time, refer to “Trouble shooting”.
Forward / Reverse switch
CAUTION:
Switch off the shredder before changing the forward /
reverse switch.
Position
e
The blades rotate in forward direction.
Position
d
The blades rotate in reverse direction to release jammed
material.
When you change the direction into
d
(reverse), keep
pushing the green button of the power switch to rotate
the blades. The shredder automatically stops when you
release the power switch.
NOTE:
Several repetitions of reverse and forward operations
may be required to shred a large object.
CAUTION:
Always use a hook or a stick to remove jammed objects
to prevent accidents.
Always wait until the shredder stops completely before
restart.
Retaining basket
CAUTION:
Switch off and unplug the machine before attaching or
removing the retaining basket.
Check the functionality of the interlock feature every
two hours for safe operation.
Never attempt to override the interlock feature of
guarding.
Lock lever:
Upper position → Retaining basket is locked.
Lower position → Retaining basket is unlocked.
The device does not switch on
because of safety function.
The machine is not switched on if the lock lever is unlock
position. The machine automatically stops if the retaining
basket is unlocked during operation.
–
–
–
–
–
–
–
–
•
•
•
•
•
•