Dodge avenger 2013 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 631

background image

As a guide, if you are shorter than average you will
prefer a lower position, and if you are taller than average
you will prefer a higher position. When you release the
anchorage try to move it up and down to make sure that
it is locked in position.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the

anchor point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,

grasp and twist the belt webbing 180 degrees to create
a fold that begins immediately above the latch plate.

3. Slide the latch plate upward over the folded webbing.

The folded webbing must enter the slot at the top of
the latch plate.

4. Continue to slide the latch plate up until it clears the

folded webbing.

Seat Belts In Passenger Seating Positions

The seat belts in the passenger seating positions are
equipped with Automatic Locking Retractors (ALR)
which are used to secure a child restraint system. For
additional information, refer to “Installing Child Re-
straints Using The Vehicle Seat Belt” under the “Child
Restraints” section. The chart below defines the type of
feature for each seating position.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

55

«
...
55
56
57
58
59
...
»

Содержание avenger 2013
























































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для avenger 2013

Бренд: Metra Electronics Страницы: 14

Бренд: Pacbrake Страницы: 9

Бренд: Daihatsu Страницы: 485

Бренд: DAVIS Страницы: 32

Бренд: FormFit Страницы: 4

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

Бренд: Axxess Страницы: 8

Бренд: Whispbar Страницы: 15

Бренд: NavLinkz Страницы: 21

Бренд: Volvo Страницы: 10

Бренд: Whispbar Страницы: 17

Бренд: Camoplast Страницы: 19

Бренд: Aries Страницы: 5

Бренд: Mercedes-Benz Страницы: 354

Бренд: Mont Blanc Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды