Doco DOCOMATIC 1200, Руководство по установке

Страница: 13 / 23

3. COMMISSIONING
If the springs are weak or broken, or the weight of the door is not balanced properly, operating the drive can lead
to uncontrolled movements of the door.
During commissioning, you must remain inside the garage. This means that you can open the door using the manual
unlocking mechanism in the event of a fault.
3.1 Menu controls
ALL FUNCTIONS, OPERATING SEQUENCES AND ADJUSTMENT & SETTING OPTIONS HAVE BEEN PRESENTED AT A GLANCE
AND AS BRIEF INSTRUCTIONS ON PAGE 8 OF THIS MANUAL!
First, loosen the screw on the light cover. Remove the light cover from the housing (FIG. 28).
OPERATING THE MENU CONTROLS
1) ENABLING (ACTIVATING) THE MENU:
Press the MENU button and hold for about 3 sec.: The green LED begins to flash, and in the multi-segment display (hereinafter
referred to as "Display") the first submenu "P" (= Program, learn drive) appears.
2) NAVIGATION WITHIN THE MENU:
You can enter the menu option displayed respectively with a single character by pressing briefly on the ENTER button ("Con-
firm selection") or switch to the next menu option by pressing briefly on the SCROLL button ("Page"); the sequence is fixed
and paging always takes place in one direction (see sequence in the description of the menu options)!
3) NAVIGATION IN THE MENU OPTION (! Please take note of the exceptions in "P" and "b" !)
If you have selected the desired menu option by pressing briefly on the ENTER button, the display then switches to a nume-
rical value between "1" and "9", which represents the status of the function or setting that has been configured: by pressing
briefly the SCROLL button, you can page through these setting options, which are always in increasing order; if the respec-
tive maximum value is reached, pressing the SCROLL button once again restarts paging with "1".
Page through the options with the SCROLL button until you reach the desired selection and confirm it by briefly pressing the
ENTER button: The display changes once again to that of the menu option, and the desired value set by you is accepted.
4) SAVE AND QUIT MENU:
The last menu option is "E" ("End"), which does not provide any setting options and merely displays the end of the menu:
Briefly press the ENTER button in order to quit the menu and to save the settings selected (green LED goes off). If you wish to
return to the menu, press the SCROLL button instead: in this case, the menu begins once again with the first menu option "P".
3.2 Programming path and force ("P")
The attachment (FIG. 7, a) must be latched and locked in the carriage (FIG. 13). The factory setting for the force (stage 5)
may not be changed before performing the learning procedure!
During the learning movement, evaluation of the light barrier and hindrance detection system or the power-opera-
ted shutdown does not take place!
Nobody may remain in the hazard zone of the garage door during commissioning and when adjustments are being
made!
• Enter (activate) the menu and go to the menu option "P" with ENTER: "1." appears in the display. Activate the drive in the
open direction by pressing the START button (display switches to "1.") and stop it just before it reaches the end position
"Door open"; move it the last few centimetres by pressing the button briefly and repeatedly in order to ensure the correct
end position.
• End the procedure by pressing briefly on the SCROLL button, enable (activate) the stand-by for closing, and "2" appears
in the display.
• Re-activate the drive by pressing the START button (display switches to "2.") and stop it just before it reaches the end po-
sition "Door closed"; move it the last few centimetres by pressing the button briefly and repeatedly in order to ensure the
correct end position.
• End the procedure by pressing briefly on the SCROLL button, enable (activate) the readiness for the subsequent learning
movement for force measurement: "3" appears in the display.
• Now press the START button briefly: the display changes to "3." and the drive performs a complete and automatic cycle
from an open condition to close, in order to obtain the exact values of the force. The display switches to "4." at the end of
the door opening movement, as well as at the beginning of the close operation. If the door is closed again, the procedure
ends, and the display indicates this status by returning to the menu: "P" appears in the display:
• Quit the menu by pressing the SCROLL button and paging to the end of the menu "E" and quit the menu with ENTER (alter-
natively: configure other desired settings in the subsequent menu options).
DOCO MATIC
13/23 04-10