background image

The DockSider”

 

Patented 

Assembly, Installation, Setup, and Operating Instruction 

OM400 - 0721 

 

 
 
 

 
       

- Beach King Mount Models;  Series 400 - 

 

  Holds Kayaks / Paddleboards up to 100 pounds. 

 

  For Beach King Docks with Adapter Track  

 

  Mounts to the Dock Siderail  

 

 

  Tools are required (7/16 & 3/4) Open End Wrenches) for initial     

        installation. 
 

A Kayak / Paddleboard Lift and Dock Storage Rack

 

Dock 

Model DS400 - Aluminum Dockside Operation 

-

 

  Operates from the Dockside Only. 

-

 

  Holds your Kayak / Paddleboard 5 to 17 inches below the dock surface. 

Some 

Assembly 
Required  

-

 

  Accommodates Freeboard (Dock Surface to Water Level) height up to 30 inches.  

Model WS400 - Aluminum Waterside Operation  

-

 

  Operates from the Waterside Only.  

-

 

  Holds your Kayak / Paddleboard 5 to 17 inches below the dock surface.  

-

 

  Accommodates Freeboard (Dock Surface to Water Level) height up to 36 inches.  

 

Please read these instructions carefully before using this product and save this 
manual for future use.  

For assistance, please call:  585 - 734 - 7374  
Or send email to:  

[email protected]

 

 

DockCraft  Industries  LLC  
  3694 Nibawauka Beach 

 

SM  

Canandaigua, New York  14424  

Page 1 of 11  

TM 

Содержание The DockSider 400 Series












Отзывы: