DMS 38MHR Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 14

DMS 38MHR Скачать руководство пользователя страница 13

13

START−UP

Test Operation

Perform a test operation after completing a gas leak and electrical
safety check. See the indoor unit installation instructions and
owner’s manual for additional start up information.

SYSTEM CHECKS

1. Conceal the tubing where possible.

2. Make sure that the drain tube slopes downward along its

entire length.

3. Ensure all tubing and connections are properly insulated.

4. Fasten the tubes to the outside wall, when possible.

5. Seal the hole through which the cables and tubing pass.

OUTDOOR UNIT

1. Are there unusual noises or vibrations during operation?

Explain the Following Items to the Customer (with the aid of
the Owner’s Manual):

1. Explain care and maintenance.

2. Present the installation instructions to the customer.

OUTDOOR UNIT DIAGNOSTIC GUIDES

For ease of service, the systems are equipped with a diagnostic code display LEDs on both the indoor and outdoor units. The outdoor
diagnostic is displayed on the outdoor unit microprocessor board.

There may be a few error codes displayed in the indoor unit that might relate to the outdoor unit’s problems. If possible, always check the
diagnostic codes displayed on the indoor unit first.

The diagnostic codes displayed on the outdoor units are listed on Table 10.

Table 10—Unit Diagnostic Guides

DISPLAY

LED STATUS

E1

Communication malfunction between indoor and outdoor units.

F0

Protection of over-current

F1

Open circuit or short circuit of outdoor ambient temperature sensor T4

F2

Open circuit or short circuit of condenser coil temperature sensor T3

F3

Open circuit or short circuit of Compressor discharge temperature sensor T5

F4

Outdoor unit EEPROM error

F5

Outdoor fan speed has been out of control

P0

IPM malfunction

P1

Over voltage or over low voltage protection

P2

High temperature protection of compressor top

P3

Outdoor low temperature protection

P4

Inverter compressor drive error

P7

Outdoor IGBT temperature sensor error

J0

High temperature protection of indoor coil in heating

J1

Outdoor temperature protection of outdoor coil in cooling

J2

Discharge temperature protection

J3

Protection of active PFC module

J4

Communication error between control board and IPM board

J5

High-pressure switch protection

J6

Low-pressure switch protection

J8

AC voltage protection

For additional diagnostic information, refer to the Service Manual.

«
...
11
12
13
14
»

Содержание 38MHR















Отзывы:

Нет отзывов