manualshive.com logo in svg

DMP Electronics XR150CAN Series, Руководство по установке

Поделиться
Скачать
DMP Electronics XR150CAN Series Скачать руководство пользователя страница 20

Digital Monitoring Products 

XR150/XR550 Series Canadian Installation Guide

16

INSTALLATION

Powered Zones for 2-Wire Smoke Detectors

11.1  Terminals 25–26 and 27–28

Panel terminals 25 through 28 provide two resettable Class B, Style A, 2-wire powered zones. For programming 

purposes the zone numbers are 9 and 10.

Note

: The maximum wire length for either zone 9 or zone 10 is 3000 feet using 18 AWG or 1000 feet using 22 

AWG. The maximum voltage is 13.8VDC and the maximum normal standby current is 1.25mA DC. The maximum 

line impedance is 100 Ohms. The maximum short circuit current is 56mA. Do not mix detectors from different 

manufacturers on the same zone.

 

Caution: 

Performing a Sensor Reset momentarily drops power to the devices on Zones 9 and 10. The panel 

views these zones (9 and 10) as “Open” while the power is absent.

Note:

 Refer to the Compliance Listing Guide (LT-1330 )for list of compatible DMP 2-wire smoke detectors.

Dry Contact Relay Outputs

12.1 Description

The XR150/XR550 Series panel provides two programmable auxiliary SPDT relays when equipped with two DMP Model 

305 relays in sockets K6 (Output 1) and K7 (Output 2) and a Model 431 Output Harness on the J2 6-pin Header. Each 

relay provides one SPDT set of contacts that can be operated by any of the functions listed below:

1) Activation by zone condition: Steady, Pulsing, Momentary, and Follow

2) Activation by 24-hour 7-day schedule: One on and one off time a day for each relay

3) Manual activation from the DMP LCD keypad menu

4) Communication failure 

12) Ready 

5) Armed area annunciation 

13) Armed

6) Fire Alarm, Fire Trouble or Supervisory 

 14) Disarmed

7) Ambush Alarm 

15) Burglary

8) Exit and Entry timers 

16) Phone Trouble

9) System Ready 

17) Device Fail

10) Late to Close 

18) Sensor Reset

11) Panic Alarm 

19) Closing Wait

Refer to the XR150/XR550 Canadian Series Programming Guide (LT-1232CAN) for specific information.

12.2  Contact Rating

The Model 305 relay contacts are rated for 1 Amp at 30VDC (allows .35 power factor). You can connect auxiliary 

power to the Relay Output 1 common terminal by installing the gray harness wire to terminal 7. Current draw for all 
connected devices must not exceed the panel maximum current rating.

12.3  Model 431 Output Harness Wiring

The relay contacts are accessible by installing the DMP 431 Output Harness on the 6-pin header labeled J2. Output 

2 uses the top three prongs, and Output 1 uses the bottom three prongs. The wire harness and contact locations are 

shown below:

Contact

Color

Output 1 normally closed

Violet

Output 1 common

Gray

Output 1 normally open

Orange

Output 2 normally closed

Violet with white stripe

Output 2 common

White with gray stripe

Output 2 normally open

Orange with white stripe

The relay contacts must be connected to devices located within the same room as the XR150/XR550 Series panel.

Содержание XR150CAN Series



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды