background image

Digital Monitoring Products, Inc  |  7000 Series Installation and Programming Guide  

42

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. 

This device may not cause harmful interference, and

2. 

This device must accept any interference received, including interference that may cause 
undesired operation.

Changes or modifications made by the user and not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.

Note

: This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

Содержание Thinline Aqualite 7000 Series

















































Отзывы: