DMC TS8000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 30

DMC TS8000 Скачать руководство пользователя страница 22

TSK8000-M REV E

TSK8000 MANUAL

©COPYRIGHT 2018 DANIELS MANUFACTURING CORPORATION

WWW.DMCTOOLS.COM

(407) 855-6161

PATENT #7,243,429

19

TS8000 Testing Procedures

Important Note from Manufacturer:

Prior to the use of this tool, the operator

should take a sample of the cable and test the strip. Adjustments in accordance with the
previous instructions may need to implemented for the best possible wire preparation
solution.

Accuracy of Strip Test

The “accuracy of strip test” allows the user to verify that the stripping of the cable and the
depth settings of the die blades meet the users requirements. The adjustable blades of the
TS8000 allow the tool to accommodate variances in cable. To properly test and adjust the
blade settings to the desired depth, follow the procedures in the operations overview (

5.0

).

Quality Check When Installing Dies

1.

Ensure die halves have the same part number.

2.

Ensure proper cable part number is being used for specific die set.

3.

Set tool to recommended depth settings and test before production.

4.

Make sure dies seat flush to one another and are fully retracted into the tool.

7.1

7.2

7.0

8.0

«
...
20
21
22
23
24
...
»

Содержание TS8000































Отзывы:

Нет отзывов