1234
1234
1234
1234
123
123
Model
Woofer
Mid
Tweeter
Nom.
Max
Sensi-
Magnet
Inst.
Mounting
Crossover
power
power
tivity
size
depth
hole bass driver
UP36i
16,5 cm / 6,5” UP2.5i
28 mm /1,1”
150 W
180 W
88 dB
62 mm / 2,44”
63 mm / 2,6”
140 mm / 5,51”
Separate box
SPEAKER FACTS FOR DLS ULTIMATE UP 3-WAY SPEAKER SYSTEMS:
CROSSOVER CONNECTION:
TWEETER & MID LEVEL
JUMPERS
Select between two different
tweeter and mid levels by
moving the small jumpers inside
the filter box.
UP1i TWEETER INSTALLATION
:
SURFACE MOUNTING:
For angled surface mount together with the angled cup:
The tweeter element is attached to the cup by fitting the three wings on
the angled cup into the tracks of the element and then turn it clockwise.
When removing the element from the cup, turn it ccw and lift it up.
RECESSED MOUNTING:
You need a hole with a diameter of 48
mm / 1,89" in the door side. Put the two
metal wings through the two tracks in the
center of the cup, just as the picture
shows, and attach them with the M4
screw and nut through the center hole.
The cup is attached to the door side
when the metal wings is pressed to the
back side of the door.
Put the tweeter element into the cup with
the cable going out through the bottom
hole. Then attach the element into the
cup and turn it clockwise to attach to the
cup. When removing the element from
the cup, turn it ccw and lift it out
INPUT WF MID TW
+ - + - + - + -
Woofer
+
-
Head unit / amp.
-2 dB
0 dB
It is very important that the baffle is stable, but it is just as important
that it is shaped in a way that allows the driver to ”breath”
backwards, otherwise there will be a lack in the drivers bass
reproduction.
Size
28 mm / 1,1"
Nom. power (RMS)
50 Watts (80 Watts max)
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
28 mm / 1,1"
Mounting depth
18 mm / 0,71"
Mounting hole
48 mm / 1,89"
Cone material
Hand treated fabric
FACTS UP1i TWEETER:
BAFFLE INSTALLATION:
Wrong way
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Bad air flow
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Correct way
with chamfer-
ed edges
Max 5 mm
Free air flow
Correct way
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
1234
Tweeter
+
-
Midrange
+
+
-
-
TW level
Mid level
Mid bass
-2 dB
0 dB
OUT
IN
Size
2,5" ( 6,3 cm)
Nom. power (RMS)
90 Watts RMS
Maximum power
160 Watts
Frequency range
400 Hz-8 kHz
Sensitivity
91 dB / W / m
Resonanst freq. / Fs
350 Hz
Magnet diameter
65 mm / 2,56”
Outer diameter
100 mm / 3,94”
Mount. depth
25 mm / 1”
Mount. hole
82 mm / 3,23”
Cone
Doped fabric
Voice coil
52 mm / 2” al flat wire
UP2,5i - MID-DOME INSTALLATION:
Should be installed high up in the door side or in the
dashboard. This speaker don´t require any box. When the
midrange is mounted high up in the dashboard the mid level
creates a frequency peak in some vehicles. If so use the low
mid level in the filter box. If the level is still too high, connect a
3-5 ohm resistor in series with the + feed.
FACTS DLS UP2.5i MID-DOME:
The
MIDBASS
jumper is used when you want to run the midbass
driver active on a separate amp. Then some components inside
the filter must be disconnected and this is done with the MID
BASS jumper
Midbass connected:
jumper in
IN
-position.
Midbass disconnected:
jumper in
OUT
-position.
