manualshive.com logo in svg

DLS MRA22, Руководство пользователя

Поделиться
Скачать
DLS MRA22 Скачать руководство пользователя страница 9

9

2. Two fullrange speakers and one subwoofer
to MRA41.

Rear subwoofer

   Rear or front speakers

Filter settings A/B Channels

The subwoofer should be connected to channel A/B
in bridge mode.The Grand Bass mode can now be
used for the subwoofer.
Set the HPF-filter switch to ON-position. Adjust the
filter setting to 25-40 Hz.
Set the LPF-filter switch to ON-position and the
Multiply swich to x1. Adjust the frequency setting to
70-90 Hz.

Filter settings C/D Channels

With the HPF-filter in OFF position the amplifier
allows the speakers to play fullrange. If you for
some reason want to limit the low bass
reproduction switch on the HPF-filter. The typical
setting is then around 60 – 80 Hz.

HPF

Off   On

50Hz 220Hz

15Hz 500Hz

Multiply

x1   x10

80/800Hz

Off   On

200/2(k)Hz

50/500Hz 500/5(k)Hz

LPF

220/2(k)Hz

MRA41

Speaker wiring MRA 41 - three different wiring examples

1. Four fullrange speakers to MRA41. One
pair in front and one pair in rear.

Rear speakers

Front speakers

Filter settings A/B Channels

With the HPF-filter in OFF position the amplifier
allows the speakers to play fullrange. If you for
some reason want to limit the low bass
reproduction switch on the HPF-filter. The typical
setting is then around 60 – 80 Hz.
The LPF-filter switch should be in OFF-position

Multiply

x1   x10

80/800Hz

Off   On

200/2(k)Hz

50/500Hz 500/5(k)Hz

LPF

HPF

50/500Hz 220/2(k)Hz

15/150Hz 500/5(k)Hz

Off   On

Multiply

x1   x10

HPF

Off   On

50Hz 220Hz

15Hz 500Hz

Filter settings C/D Channels

With the HPF-filter in OFF position the amplifier
allows the speakers to play fullrange. If you for
some reason want to limit the low bass
reproduction switch on the HPF-filter. The typical
setting is then around 60 – 80 Hz.

HPF

50/500Hz

15/150Hz 500/5(k)Hz

Off   On

Multiply

x1   x10

Содержание MRA22















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды