manualshive.com logo in svg

DLS MRA22, Руководство пользователя

Поделиться
Скачать
DLS MRA22 Скачать руководство пользователя страница 7

Two fullrange speakers to MRA22

With the HPF-filter in OFF position the amplifier
allows the speakers to play fullrange. If you for
some reason want to limit the low bass
reproduction switch on the HPF-filter.
The typical setting is then 60 – 80 Hz.

The LPF-filter should be OFF.

One subwoofer connected in bridge mode to
MRA22

The HPF filter is here used as subsonic filter to take
away the very deepest frequencies. The typical set-
ting is around 25 – 40 Hz.

The LPF  will allow low frequencies only and blocks
higher frequencies. A typical setting is 70 – 90 Hz.

LPF

Off   On

80Hz 200Hz

50Hz 500Hz

Filter settings

NOTE!

4 ohm minimum load when using bridge mode
connection. Lower impedances may damage the
amplifier. In bridge mode the amplifier sees a 4
ohm load as 2 ohm.

Filter settings

MRA22

Speaker wiring MRA 22

HPF

Off   On

50Hz 220Hz

15Hz 500Hz

HPF

Off   On

50Hz 220Hz

15Hz 500Hz

LPF

Off   On

80Hz 200Hz

50Hz 500Hz

7

Содержание MRA22















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды