28
5. Programming the ARTROMOT®-F
Before programming
Ensure the device is completely assembled
prior to operation
1. Attach the cable (19) from the hand-held
programming unit to the CPM actuator.
2. Install batteries, or plug the AC adapter
into the hand-held programming unit
and a grounded wall outlet.
3. Turn the device on and off from the
POWER ON/OFF button on the hand-
held programming unit. The LCD displays
shows the current range of motion
position of the device.
4. Before programming
ARTROMOT®-F
,
ensure the device is not running. If it is,
stop the device by pressing START/STOP
button on the hand-held programming
unit.
Speed
„+“ key
Extension
LCD-Display
Flexion
„–“ key
START/STOP-
key
Pause
SET-key
5.1 Programming steps
Programming Range of Motion
1. Turn the device on by pressing the
POWER ON/OFF button on the hand
controller. The hand-held programming
unit momentarily flashes all the system
icons and then permanently displays the
present range of motion.
2. Press the
SET button
(system icons
flash). The yellow SET light will appear
indicating that the hand controller is
ready to receive new programming.
3. To program
extension
press
EXT button
.
The LCD will display the extension icon
and the currently programmed extensi-
on setting.
4. To program the desired amount of
extension, press the
+ and – buttons
to
increase or decrease the range.
5. To program
flexion
press the
FLEX
button
. The flexion icon will appear in
the LCD display.
6. To program the desired amount of fle-
xion, press the
+ or – buttons
to adjust
the demanded range.
7. Once programming is complete, press
the
SET button
again to store the
settings in the hand-held-programming
unit (yellow light will go off).
Or, continue setting other operating
features.
8. To start the treatment press
START/
STOP button
on the hand controller.
Programming Speed
1. With power on, press the SET button.
The yellow light will appear indicating
that the controller is ready to receive
new programming. The LCD will flash all
system icons.
2. Press the
SPEED button
. The LCD now
only displays the SPEED icon
and the currently programmed speed
setting. There are
4 speed settings
:
1 is the lowest, indicated by a tortoise,
and 4 is the fastest, indicated by a hare.
3. To increase or decrease speed,
press the
+ or – buttons
.
4. When programming is complete,
press the
SET button
again to store the
setting in the hand controller (yellow
light will go off). Or do not press the
SET button but continue setting other
operating features.
MOT-301-DE_USA-GB_Rev_03-04-01-2017_DV3.indd 28
17.01.17 10:10
Содержание ARTROMOT-F
