background image

www.pcessflight.com 
 

12 

 

 

 

 

CONFIGURATION BY ASSISTANT ON A PC 

1. Power on the PC. Make sure your computer is connected to the Internet for the first time you 
use.  

2. Switch on the transmitter first, and then power on the autopilot system. Connect the autopilot 
system to the PC with a Micro-USB cable. DO NOT break the connection until setup is finished.  

3. Run the Assistant Software.  

4. Observe the indicators on the left bottom of the software. (They are the connection indicator 
and  communication  indicator  in  order.)  If  the  communication  indicator  is  blinking,  that  the 
software is ready,  

please go to next step.  

5. Select the “Info” option. Check the software firmware version. If the upgrade is available, 

you may update the assistant software. 

6. Select the “Upgrade” option. Check the Main Controller, GPS and IMU fi

rmware version.  

7.  Select  the  “Basic”  option.  Please  follow  step

-by-step  for  your  first-time-configuration.  Basic 

configuration is necessary, including Mixer Type, Mounting, RC, and Gain settings.  

8. You can click the “Advanced” option for more parameter

 settings. Advanced setting is optional. There 

are settings of Motor, Failsafe, Intelligent Orientation Control (IOC), Gimbal, Low-Voltage Alert, and 
Flight Limits. Read the instruction in the assistant software to obtain more details.  

9. Select the “Viewer” option to check all parameters.  

 

10. Then break the Micro-USB cable, power off the aircraft. Finished. 

 

 

 

 

 

 

Содержание NAZA-F45


















Отзывы: