background image

Left stick / Up (Slowly)

Start / Stop the motors

OR

8

1

The App

RTH Button

●  

If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.

3

6. Preparing the Aircraft 

The aircraft is in Travel Mode during delivery. Follow these steps to change it 

to Landing Mode before your first flight:

    Insert the Intelligent Flight Battery into the battery compartment.

    Power on the remote controller and the Intelligent Flight Battery.

    Toggle the Transformation Switch up and down at least four times. Repeat 

to change aircraft to Travel Mode.

    Power off the aircraft before mounting the gimbal and camera.

Travel Mode 

Landing Mode

2

1

5. Preparing the Remote Controller

Tilt the Mobile Device Holder to the desired position then adjust 

the antennas as shown. The strength of the remote controller 

signal is different when the antenna position is different.

The transmission signal between the aircraft and remote 

controller will perform best when within the optimal 

transmission range. If the signal is weak, fly the aircraft 

closer to you to achieve optimal signal performance.

1

3

2

Strong 

Weak

UP

Down

Tu

rn R

igh

t

Tu

rn

 L

ef

t

UP

Down

Tu

rn R

igh

t

Tu

rn

 L

ef

t

Forward

Backward 

Rig

ht

 L

ef

t

Forward

Backward

Rig

ht

 L

ef

t

Left Stick

Right Stick

1

5

6

7

8

1

2

5

6

3

4

7

Gimbal Cover

Gimbal Connector

Mounting Place

Gimbal Lock

Locked

2

3

1

High

B

A

A

  

While returning home, its 
altitude can be adjusted by the 
user to avoid obstructions.

Before taking off, make sure the aircraft 

status bar in the DJI Pilot app shows “Safe 

to Fly (GPS)”. Otherwise, the aircraft cannot 

hover in place and record the Home Point.

10. Flight

●  

Manual Take - off & Landing:

Safe to Fly (GPS)

●  

Auto Taking - Off & Landing:

Tap           and confirm your selection. The aircraft will automatically take off, retract 
its landing gear, and hover at 1.5 meters after you tap and confirm Auto Take-off.

1

4. Charging

Using INSPIRE 1

  

You can set the remote controller to different modes using the DJI Pilot app.

  

Do not use other 2.4GHz devices at the same time to avoid signal interference. 

1. Download the 

DJI Pilot

 App

Visit http://m.dji.net/djipilot or scan this QR code to 

download the 

DJI Pilot 

app

 

through your mobile device. 

7. Mounting the Gimbal and Camera

3. Check Battery Levels

Press the Power Button once on both the Intelligent Flight Battery and remote controller to check battery levels. The 

Intelligent Flight Battery must be fully charged before using it for the first time. Make sure both batteries are adequately 

charged before each flight.

Press the power button once then press again and hold for 2 seconds to power on the remote controller. Repeat to power off.

Press the power button once, then press again and hold for 2 seconds to power on the Intelligent Flight Battery. Repeat to 

power off.

9. Remote Controller Operation

The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ). 

Adjust the tilt angle of camera by using the Gimbal Dial.

  

For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).

  

Read the Inspire 1 User Manual in the DJI Pilot app or official DJI website for more details.

 

 When not in P mode, the Inspire 1 will only maintain altitude, not position, and will drift with 

wind or user inputs. Return to Home is not available in F mode.

 

 

Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller. 

 

 

To charge the Inspire 1 Intelligent Flight Battery or the remote controller, connect it to power through the port to a 

suitable power source (100-240V 50/60Hz). 

  

It is recommended to turn off the batteries before charging. 

 

 

Use the included charger to charge the Intelligent Flight Battery and the remote controller battery. When fully charged, the 

battery LEDs on the Intelligent Flight Battery and remote controller will turn off.

Watch the tutorial videos at www.dji.com or in 

the DJI Pilot app.

2. Watch the Tutorial Videos   

The tutorial videos 

Press the button on the side of the Mobile 

Device Holder to release the clamp. 
Place your device onto the clamp and adjust 

the clamp to hold it securely.
Connect your mobile device to the remote 

controller with a USB cable. Plug one end of 

the cable into your mobile device, and the 

other end into the USB port on the back of 

the remote controller.

Remove the Gimbal Cover.

Rotate the Gimbal Lock to the unlocked position (to the right when 

facing the nose of the aircraft). Insert the gimbal by aligning the 

white mark on the gimbal with white mark on the Gimbal Lock. 

Rotate the gimbal lock back into the locked position (to the left 

when facing the nose of the aircraft). 

1

Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode 

is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the 

self-check. 
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the 

aircraft if it fails to connect. Refer to the 

INSPIRE 1 User Manual

  on how to link. 

Ensure the remote controller and your mobile device are connected with a USB cable. Launch the 

DJI Pilot app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI Pilot app and tap “Camera”. Ensure the aircraft is functioning normally by 

completing the Checklist.Beginner Mode is enabled by default when you launch the DJI Pilot app 

for the first time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode. 

We recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable 

Beginner Mode in the settings page of the DJI Pilot app. 
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then 

follow the on-screen instructions.
For 1345s Propeller, install the propellers with a white dot onto the mounting plates that have a white dot, 

and install the propellers without a white dot onto the mounting plates that do not have a white dot. Press 

the propeller down onto the mounting plate and rotate in the lock direction until secure. 
For 1345 Propeller, attach propellers with the black nut onto motors with the black dot and spin 

counter-clockwise to secure. Attach propellers with gray nut onto motors without a black dot and spin 

clockwise to secure. Place all propellers onto the correct motor and tighten by hand to ensure security 

before flight.

8. Preparing for Flight

Place the aircraft on a flat surface, in an open space, with the back facing you.

Appendix

Aircraft
Status Indicator Description 

Slowly: Safe to fly,GPS working

Slowly: P-ATTI or ATTI

Quickly: Not connected
to remote controller

Slowly: Low battery level warning

Quickly: Critical low battery level warning

Solid: Critical error

Blinking Alternately:
Compass calibration required

Double: Vision Positioning 
System working, no GPS

X

2

www.dji.com/product/inspire-1

Gently pull the left (throttle) stick down to lower the aircraft 

until it touches the ground. Pull both sticks to the bottom 

inside corners to stop the motors. 

After flight, change the aircraft back into Travel Mode. Do not 

attempt this at the beach, over grass, or over monochromatic 

carpet. Then place the aircraft on a flat surface and remove 

the gimbal and camera for transport.

●  

Return to Home 

Start the motors by pulling both control sticks to the bottom inside (or outside) 

corners. Release the sticks once the motors start. Slowly push the left (throttle) 

stick up to take off. Once in the air, toggle the Transformation Switch up to 

raise the landing gear.

Remote controller is functioning normally
but is not connected to the aircraft.  

Remote controller is functioning normally
and is connected to the aircraft.  

Remote controller is in Slave Mode
and not connected to the aircraft.  

Remote controller is in Slave Mode
and is connected to the aircraft. 

B-B-B... Aircraft low battery warning
 

or remote controller error. 

B—B—...  Remote controller has been
 

idle for 5 minutes. 

Remote Controller
Status LED

Using the Camera

● 

 

Adjust the camera parameters using the 
Camera Settings Dial on the remote 
controller or through the DJI Pilot app. 
Press the Shutter Button/Video Record 
Button to capture photos or record 
videos.

● 

 

Adjust the tilt of the gimbal using the 
Gimbal Dial.

● 

 

Download photos and video from the SD 
card to your mobile device through the 
DJI Pilot app. You may also use a SD 
card reader to export files to your PC.

1. Press and hold the return home 

button until the LED surrounding 
the button is blinking white, and the 
return home procedure is in 
process. Press once to stop the 
procedure.

2. The DJI Pilot app notifies users to 

take action when the battery level 
falls to a specified threshold. This 
warning threshold can be set 
within the DJI Pilot app. The 
aircraft will land immediately when 
it reaches Critical Low Battery 
Level Warning.  

3. Failsafe: The Inspire 1 will enter 

RTH mode if remote controller 
signal is lost.

DJI Pilot app

INSPIRE 1

www.dji.com

Creativity Unleashed

Gimbal Dial

( In the Camera screen of the DJI Pilot app )

Tap           and confirm your selection. The landing gear will lower and the aircraft 
will automatically land.

 

 It is highly recommended that you only take off when the Aircraft Status bar is green.

 

 The aircraft cannot take off if the Critical Low Battery Warning is active. 

 

The  Intelligent  Flight  Battery  must  warm-up  if  the  outside  temperature  is  low.  A 

warning will display in the DJI Pilot app.

 

 Rotating propellers can be dangerous. Do not start the motors when there are people 

nearby and always fly in a wide open area. 

 

 

Never stop the motors during flight. Power off the aircraft prior to switching off the 

remote controller after landing.

©

2014 DJI. All Rights Reserved

 Designed by DJI. Printed in China.

Learn more information from:

Left stick / Down (Slowly)

RTH Button

Low

Battery Level 

Low

High

Battery Level 

Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 for the first time: 

Inspire 1 Quick Start Guide, Disclaimer, Intelligent Flight Battery Safety Guidelines, Inspire 1 Safety Guidelines, In the Box,

Inspire 1 User Manual.

If you have purchased an Inspire 1 with dual remote controllers, the Master remote controller will connect to the aircraft 

automatically when powered on. Master/Slave mode is disabled by default. Activate it and set it up through the DJI Pilot 

app. The Master remote controller’s Status LED will show solid green when it connected to the aircraft. The Slave 

remote controller’s Status LED will show solid blue when it is connected to the Master controller. 
Connecting the Master remote controller to the Slave remote controller:

On the Master remote controller, launch the DJI Pilot app and go to the Camera page. Then tap          on the top of your 

screen to enter the remote controller settings window. Tap “Activate Master/Slave Mode”and select “Master”. Then 

enter your desired connection password for the “Slave” remote controller.

On the Slave remote controller, select “Slave “ and tap “Search” to find the Master remote controller. Select the “Master” 

remote controller from the “Master RC List” and input the connection password.

DJI Pilot 

App

Toggle the 

Transformation 

Switch up

B

Содержание Inspire 1 V1.2











Отзывы: