dji Inspire 1 V1.2, Быстрый старт

Страница: 5 / 10

11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
YC.BZ.S00101.02
Return to home
Vision Positioning
Altitude 2.5 m
GPS Positioning
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19 20
11
14
13
12
16 15
6
1 3
2
5
9
5
8
6
6
7
7
7
14
15
10
11
12
13
4
45
1
mm
43
8
m
m
301 mm
Quick Start Guide
INSPIRE 1
The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers,
it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 22m/s* and a maximum flight time of 18 minutes
*
using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person can
fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz wireless
signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has a maximum
run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that maximum flight speed and maximum run time were tested in a lab environment. These statistics are for reference only, as
conditions in your area may vary.
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your
area may vary.
INSPIRE 1 Remote Controller
Folded
●
Environmental Considerations:
1. Do not fly in severe weather conditions. This includes high wind, snow, rain and smog.
2
.
Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the onboard compass and GPS signal.
3
.
Avoid from obstacles, crowds, high voltage power lines, trees or bodies of water.
4
.
Minimize electromagnetic interference by not flying in areas with high levels of electromagnetism, including mobile
phone base stations or radio transmission towers.
5
.
Aircraft and battery performance is subject to environmental factors such as air density and temperature. Be very careful when
flying 14700 feet (4500 meters) or more above sea level as battery and aircraft performance may be reduced.
6
.
The Inspire 1 cannot operate in P mode or use GPS at polar latitudes. It only can fly in ATTI mode and use the Vision Position-
ing System.
Fly Safe
Appendix
● P Mode:
Safe to fly. In this mode, the Inspire 1 has a strong GPS signal and
can use the Vision Positioning System allowing it to hover accurately
in position indoors and out. If outdoors, this mode also means that a
Home Point has been locked so that it can Return to Home if the
control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
Vision Positioning System to hover accurately. P-ATTI: Neither
GPS or Vision Positioning System available, aircraft is using only
its barometer for positioning, so only altitude is controlled.
Note that the Vision Positioning System may not work properly when
the Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
●
Return to Home:
When the GPS signal is strong, the aircraft will be able to record a
Home Point and return to the Home Point when needed. The GPS
location is recorded when the GPS signal icon in the DJI Pilot app is
either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller
or in the App. Low Battery RTH: The DJI Pilot app notifies users to take
action when the battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
●
While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal.
The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
V1.2
If you are not in this mode, toggle the Flight
Mode Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
●
Aircraft (Model: T600)
Weight (Battery Included) 2935 g
Maximum Weight of Payload 3400 g
Max Tilt Angle
35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 22 m/s (ATTI mode, no wind)
Max Flight Altitude 4500 m
Max Flight Time Approximately 18 minutes
Operating Temperature Range -10°C to 40°C
●
Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
●
Vision Positioning
Velocity Range <8 m/s (Altitude 2 m)
Altitude Range 5 cm-500 cm
Operating Environment Surface with clear pattern and adequate lighting (Lux > 15)
Operating Range 0-250 cm
●
C amera (Name/Model: X3/FC350)
Sensor Sony EXMOR 1/2.3”Effective pixels:12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000x3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD (4K): 4096x2160p 24/25, 3840x2160p 24/25/30
FHD: 1920x1080p 24/25/30/48/50/60 HD: 1280x720p 24/25/30/48/50/60
Max Bitrate Of Video Storage 60 Mbps
Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range 0°C to 40°C
●
Remote Controll er (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance 2 km (outdoor and unobstructed)
Video Output Port USB, Mini-HDMI
Operating Temperature Range -10°C to 40°C
Battery
6000 mAh LiPo 2S
●
Charger (Model: A14-100P1A )
Voltage 26.3 V
Rated Power 100 W
●
Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
●
Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.6 Wh
Net Weight 670 g
Operating Temge -10°C to 40°C
Max Charging Power 180 W
18
2
m
m
172
m
m
105 mm
71 mm
●
Flight Limits:
The Inspire 1 is not permitted to fly within no-fly zones as specified
by local laws and regulations. Please visit here:
http://flysafe.dji.com/no-fly
for more information.
FCC ID ： SS3-WM6101410 FCC ID ： SS3-GL6581502
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock
Connect to the
mobile device
●
Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance. Recalibrate the compass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a
new location.
●
DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
●
DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
●
DO NOT calibrate beside massive metal objects.
●
If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing
the aircraft on the ground, the compass has detected magnetic interference. Change your location.
21