DIY-Thermocam V2 Скачать руководство пользователя | Manualshive

Страница: 16 / 22

background image

16.

• Put the lithium battery in place like shown on the image, but do not connect it so

far

• Solder the wires of the push button to the two pins labeled BUTTON, the direction

does not matter. It is good to put some solder on the pins first, then on the cables,
and afterwards put those two together

• Next, solder the wires of the power switch to the two pins labeled SWITCH, the

direction does not matter

• Lastly, solder the three wires of the external USB switch to the connection labeled

EXT-POWER

• Take care to keep the chronology order, so top to top, middle to middle, bottom to

botttom

DIY-Thermocam V2 Assembly Guide

Page 16

DIY-Thermocam V2 Assembly Guide

«
...
14
15
16
17
18
...
»

Содержание V2























Отзывы:

Нет отзывов

Похожие инструкции для V2

Бренд: Panasonic Страницы: 15

Бренд: Federal Signal Corporation Страницы: 20

Бренд: Zavio Страницы: 42

Бренд: Zavig Страницы: 10

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 104

Lumix DMC-GH2EB

Бренд: Panasonic Страницы: 200

Бренд: Panasonic Страницы: 82

Бренд: iDeaPLAY Страницы: 14

Бренд: Olympus Страницы: 74

PowerShot ELPH 320 HS IXUS 240 HS

Бренд: Canon Страницы: 106

Бренд: ViewSonic Страницы: 2

Бренд: SunBriteTV Страницы: 42

Бренд: SBIG Страницы: 47

Бренд: Hama Страницы: 288

Бренд: Alecto Страницы: 2

Auto Capsule AQ2

Бренд: Cowon Страницы: 30

Бренд: Pentax Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды