DIY BBQ Angela 'L' Island Скачать руководство пользователя

Страница: 2 / 48

If you are still having trouble putting your module together, we are here to help. Contact us at 800-289-3492 or email [email protected].

Warnings

Notice of Limited Liability

Arbitration Agreement

This instruction manual is protected under Copyright Law of the United States of America.

This copy of the instruction manual is for the sole use of the original purchaser. A license to use the information contained herein is granted to

the original purchaser by the author.

No part of this instruction manual, including but not limited to, photographs, pictures, diagrams, or illustrations may be reproduced, copied or

transferred in print or electronically to third parties without the express written permission of the author. Any copying, retransmission, editing or

distribution without the express written permission of the author will terminate the license and all copies in the possession or distribution by the

purchaser will be considered unlicensed and therefore in infringement of U.S. Copyright Law.

Furthermore, if the purchaser wishes to use the information contained herein for the creation or supplement of business, whereby BBQ islands

would be part of the business, then the purchaser is not permitted to use or distribute any of the enclosed information within that business without

the express written permission of the author.

When working with metal, the edges are very sharp and may have small splinters across the edges. Be extremely careful when handling each piece.

It is highly recommended to wear safety glasses and gloves at all times while building your modules. Eye protection is required when cutting or

screwing metal pieces to protect against errant metal pieces and particles.

Keep children and animals away from the metal pieces and completed frame kits.

Please follow all manufacturer directions on how to properly install BBQ products.

Check with your local codes on construction for the required permits you may need for construction of your BBQ island.

Utility lines should only be installed by a licensed plumber or electrician per the code in your area. Do not forget to get a permit if required by

local laws or regulations.

Please read all directions on how to install your DIYBBQ island modules. Installation of the product is at your own risk; DIYBBQ, LLC is not

liable for misuse of the module frame kits nor for damage to any of your BBQ products.

NOTICE: DIYBBQ, LLC shall NOT be liable for incidental and consequential damages, directly or indirectly sustained to any person(s),

equipment, tools, or appliances during or after the installation of any BBQ island, related directly or indirectly to the installation and operation

of any BBQ island or appliances, nor for any loss caused by application of these goods not in accordance with current printed instructions or

for other than the intended use. DIYBBQ, LLC’s liability is expressly limited to replacement of defensive goods. Any claim shall be deemed

waived unless made in writing to DIYBBQ, LLC at 26520 ADAMS AVE., MURRIETA, CA 92562 within thirty (30) days from the date it

was or reasonably should have been discovered.

USE OF OR PURCHASE OF ANY DIYBBQ, LLC PRODUCTS, OR ANY GOODS AVAILABLE FOR PURCHASE THROUGH

DIYBBQ.COM REQUIRES THAT ALL CLAIMS BE SETTLED UNDER THIS BINDING ARBITRATION PROVISION, WHICH

AFFECTS YOUR LEGAL RIGHTS AND MAY BE ENFORCED BY EITHER PARTY.

In the event a dispute shall arise between DIYBBQ, LLC and any purchaser of any DIYBBQ, LLC product or good available through

diybbq.com, it is hereby agreed that the dispute shall be referred to a USA&M office to be designated by USA&M National Headquarters for

Arbitration in accordance with the applicable United States Arbitration and Mediation Rules of Arbitration.

The arbitrator’s decision shall

be final and legally binding, and judgment may be entered therein.

Each party shall be responsible for its share of the arbitration fees in accordance with the applicable Rules of Arbitration. In the event a party

fails to proceed with arbitration, unsuccessfully challenges the arbitrator’s award or fails to comply with the arbitrator’s award, the other party

opposing party is entitled to costs of suit, including a reasonable attorney’s fee for having to compel arbitration or defend or enforce the award.

Содержание Angela 'L' Island
















































Результаты поиска

Содержание Angela 'L' Island

Отзывы:

Похожие инструкции для Angela 'L' Island

Бренды по названию

Популярные бренды

DIY BBQ Angela 'L' Island, Инструкция по эксплуатации

Результаты поиска

Содержание Angela 'L' Island

Отзывы:

Похожие инструкции для Angela 'L' Island

Бренды по названию

Популярные бренды