Dixon ZTR 5421 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 43

background image

MOWER DECK INSTALLATION

NOTE:

Brake link (P/N 5283) normally used for installation of engine to mower deck drive belt,
has been placed in position during assembly of the lift frame at the factory. For shipment
purposes, the brake link has been secured with a cotter pin and washer. REMOVE AND
DISCARD cotter pin and washer after engine to mower drive belt has been installed.

1.

Loosen and remove front body mounting bolts (P/N 3368) and washers (P/N 3066).
Disconnect headlight wiring plug from wiring harness. Lift front body from chassis.

2.

Install rear hanger rods on lift frame. Slide lift plate on hanger rods, small holes in lift
plate will face rear of mower, and start nylok nuts on each hanger rod until approximately
1/2 inch of threads are exposed.

3.

Position mower deck under chassis.

4.

Raise front of mower deck and slide front support rod through lift frame and tabs on

mower deck. Install hair pin clips on front and rear of support rods.

5.

Move lift lever to lowest cut position, install engine to mower deck drive belt on top center
pulley. Check belt routing after installation to make certain that belt is centered in
groove of electric clutch pulley.

6.

Move lift lever toward high cut position and remove brake link from hole on lift lever.

7.

Install front body, connect headlight wiring.

Page 9

«
...
10
11
12
13
14
...
»

Содержание ZTR 5421












































Отзывы:

Нет отзывов

Похожие инструкции для ZTR 5421

Бренд: Gardol Страницы: 171

Бренд: Rally Страницы: 19

COMPANION 27826

Бренд: COMPANION Страницы: 84

Бренд: Jacobsen Страницы: 98

ELM 42/1800 PLUS

Бренд: F.F. Group Страницы: 52

Бренд: MTD Страницы: 37

Бренд: Kees Страницы: 23

Бренд: Flymo Страницы: 10

A12612A Stockman PRO

Бренд: COX Страницы: 48

LMO 18-36 Battery

Бренд: Kärcher Страницы: 252

Бренд: Gardif Страницы: 22

Бренд: VonHaus Страницы: 12

Бренд: Toro Страницы: 24

Бренд: MDL POWERUP Страницы: 26

Бренд: Makita Страницы: 252

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 72

Бренд: Makita Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды