background image

 

CARE AND MAINTENANCE - MODELS ZTR 4423 & ZTR 4424

 

DRIVE SYSTEM ADJUSTMENTS:

 

Due to both the complex nature of the transmission and the number of special  tools 
required for service, adjustments should be entrusted to your dealer.

 

There are a number of simple owner service items which greatly influence the 
performance of the drive system.

 

1.     Front and rear tires must be inflated to proper specifications.

 

2.     Rear drive chain tension.

 

3.     Tightness of all controls and linkages pertaining to the drive levers.

 

4.     Lubrication of both primary and final drive chains. The use of a high quality chain 

lubricant is highly recommended.

 

 

REAR CHAIN ADJUSTMENT:

 

Proper tension for the rear drive chains is accomplished through the use of an "automatic" adjuster 
located at mid-point of each rear chain.

 

Maintenance:

 

Periodically remove any build up of grass, mud or other debris from both the spring loaded roller and the 
upper guide rod. The use of a penetrating lubricant on the springs and rod is recommended as a rust 
preventative.

 

 

 

Page 29

 

Содержание ZTR 4000 series








































Отзывы: