background image

37

mAIntenAnCe

Safety System

the machine is equipped with a safety system that 
prevents starting or driving under the following 
conditions.
the engine can only be started when:

the mower deck is disengaged.

1. 

the steering controls are in the outer, locked 

2. 

neutral position.
the parking brake is on.

3. 
make daily inspections to ensure that the safety 
system works by attempting to start the engine 
when one of the conditions is not met. Change the 
conditions and try again.
If the machine starts when one of these conditions 
is not met, turn the machine off and repair the safety 
system before using the machine again.
make sure the engine stops when the park brake 
is not engaged and the operator leaves the seated 
position.
Check that the engine stops if the mower blades are 
engaged and the driver temporarily moves off the 
drivers seat.

IMPORTANT INFORMATION

In order to be able to drive, the driver must 
sit in the seat and release the parking brake 
before the steering controls can be moved into 
the neutral position, otherwise the engine will 
stop.

8058-078

Steering controls locked in neutral

Parking Brake

Visually check that no damage is found on the lever, 
cables, or switch belonging to the parking brake. 
Perform a standstill test and check that there is 
sufficient braking action.
to adjust the parking brake, contact the Dixon service 
workshop.

IMPORTANT INFORMATION

The machine must be absolutely standing still 
when applying the parking brake.

8058-080

Parking brake

WARNING!

Faulty adjustment will result in 
reduced braking ability and can 
cause an accident.

Содержание SPDZTR 42

































































Отзывы: