Dixon DX254 / 966651201 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 68

Dixon DX254 / 966651201 Скачать руководство пользователя страница 50

tRoUbleshootIng gUIDe

50

Problem

Cause

Engine will not start

• Blade switch is engaged
• Steering controls are not locked in the neutral

position

•  Parking brake is not activated
•  Battery is dead
•  Contamination in the carburetor or fuel line
•  Fuel supply is closed or the tap for the fuel tank is

in the wrong position

• Clogged fuel filter or fuel line
• Faulty ignition system

Starter does not turn the engine over

• Dead battery
• Poor contacts on the battery terminal cable

connections

•  Fuse blown
•  Ignition system faulty
•  Fault in the starter safety circuit See

Safety

System

in the

Maintenance

section

Engine runs rough

•  Faulty carburetor
•  Choke control is pulled out with warm engine
•  Clogged fuel filter or jet
•  Clogged ventilation valve on the fuel cap
•  Fuel tank nearly empty
•  Fouled spark plug
•  Spark plug is loose
•  Rich fuel mixture or fuel-air mixture
•  Wrong fuel type
•  Water in the fuel
•  Clogged air filter

Engine seems weak

•  Clogged air filter
•  Fouled spark plugs
•  Carburetor incorrectly adjusted

«
...
48
49
50
51
52
...
»

Содержание DX254 / 966651201





































































Отзывы:

Нет отзывов