manualshive.com logo in svg

Dixon DX254 / 966651201, Руководство оператора, Страница: 23 / 68

Поделиться
Скачать
Dixon DX254 / 966651201 Скачать руководство пользователя страница 23

1

2

ContRols

23

80650-601

Choke control

Choke Control

The choke control is used for cold starts to provide 
the engine with a richer fuel mixture.
For cold starts the control should be pulled out to its 
extent.

Fuses

Fuses are located on the right hand side of the 
machine. They are accessed by tilting the seat 
forward. Fuses are flat pin fuses type as used in 
automobiles.
There are three fuses with ratings and functions:
1.  20 A, Primary fuse.
2.  7.5 A, Mower deck coupling.
3.  10 A, Accessories

8065-043

Fuses

Cutting Height Pedals

The cutting height pedals release the deck lift to allow 
setting the desired deck height. Apply pressure to the 
lift pedal and rotate foot to also apply pressure to the 
release pedal, unlocking the deck lift. 
For transport, push the lift pedal fully forward until the 
deck lift latches in the transport (highest) position.

8065-017

1. Lift pedal 
2. Release pedal

Cut height selection pedals

Содержание DX254 / 966651201





































































Отзывы:

Нет отзывов