090082 R7
IMPORTANT:
This elbow is designed for use with standard 4” top seal
service station adapters. To properly operate and maintain your Bayco “6400
series” elbow the following instructions are provided. Please read with care
as improper handling or maintenance may cause a hazardous condition.
CAUTION:
Do not modify your Bayco 6400 series elbow for any reason. It
can result in a hazardous condition due to operating difficulties or
operation malfunction. Disassembly or tampering will void the
product warranty.
Never smoke or allow an open flame near your dispenser when
handling volatile materials such as gasoline and fuels. An explosion
could result. Remember safety is everyone’s business.
Installation:
When the 6400 Series elbow is shipped, the sight glass and
gaskets are in a plastic bag attached to the elbow. These must be
installed with the required mating Bayco inlet (3” or 4” male or female
purchased separately). Take the sight glass and gaskets out of the
plastic bag and place one gasket inside the elbow inlet end and
make sure it is sealed evenly.
Carefully (keep straight) slide the
sight glass into the inlet end and onto the installed gasket. Place the
other gasket inside the inlet and on the sight glass.
Attach the
mating inlet using the four socket head cap screws supplied. Coat
cap screws with anti-seize compound.
Lubricate Stem:
This product has been assembled with anti-seize
compound and lubricated for easy maintenance and trouble-free
service. However, we recommend lubricating the stem through the
grease nipple using lithium based or quality automotive type grease
prior to service.
It is recommended to apply lubricant to grease
nipple, cam arm bearings, and other moving parts every month.
Monthly inspection and lubrication become mandatory for items
that are seldom used. Condensation, rain and road salts can
cause corrosion build-up and binding when product not in use.
Check Operation:
Place elbow bottom end on service station adapter (elbow
is designed for use with 4” top seal adapter only). Move operators
handle to 11 o’clock the open/unclamped position. Release and hold
the safety latch if equipped with one. Move the handle clockwise to 2
o’clock position for full clamping (lever cannot be moved any farther).
Check locking arms on adapter. If the elbow is fitted with a safety
latch, make sure the stem pin is in the latch notch, preventing
movement of operating handle.
Release by moving handle to 11
o’clock. If fitted with safety latch, lift the latch lever and operating
lever at the same time.
Care & Handling:
Bayco drop elbows are tested at the factory and are in
proper working condition when shipped. Drop elbows are designed to
be tough and to provide long service with reasonable care and
handling. To ensure long service Bayco elbows should not be
thrown, dropped or dragged; such actions may compromise the
integrity and reduce the service life of the product.
Inspect for Damage:
Drop elbows can fail to operate if not properly
maintained.
If the #6400 elbow develops any problems, remove
from service and contact your Dixon Bayco distributor describing the
difficulty.
Elbows should be inspected monthly
. Check the main
gasket seal, the sight glass, and the flange where the base is
attached to the elbow body for any signs of leakage. Change seals if
necessary. Check the sight glass for cracks or damage and replace
if needed. Check and tighten all fasteners periodically. Lubricate the
lever stem. Check the bushings and replace if cracked or worn, and
change if required. Check operation as per above.
Regularly Replace Bushings:
All Bayco 6200 and 6400 series elbows
contain polymer bushings, which protect and extend service life of
bronze locking arms. The bushings are designed to wear (instead of
the bronze arms) and should be replaced every few months.
Operators must be encouraged to inspect and replace polymer
bushings to obtain maximum elbow performance and longevity.
Optional Accessories:
The following accessories are included on specific
6400 elbows, and are available as add on options for other 6400
elbows.
Safety latch kit # 6200SLK
and
extension kit # 6400EXT
.
Installation instructions are included with the items when ordered for
retrofit.
Dixon Bayco Warranty
: For complete warranty information, please refer to
the inside back cover of the latest Dixon catalogue.
Содержание BAYCO 6400
Страница 1: ...090082 R7...
