dixell XB590L Скачать руководство пользователя | Manualshive

Страница: 5 / 32

background image

1592006230 XB590L GB r1.0 29.02.2016

XB590L

5/32

3. MOUNTING & INSTALLATION

The

XB590L

can be fitted to the back panel, with a 150x31mm hole, and fixed with 2 studs 165mm apart. To

increase protection, use the rear-front protective rubber mod.  PG-L (optional). To apply the polycarbonate in
the front panel, drill a hole in the panel as shown in chapter 3.1.
The  ambient  operating  temperature  range  is  from  0÷60°C  (RH  20÷85%).  Avoid  locations  subject  to  heavy
vibration,  corrosive  gases  or  excessive  dirt.  The  same  warnings  have  to  be  applied  to  the  probes.  Ensure
enought ventilation around the instrument.

3.1 CUT OUT FOR FRONT OR BACK-PANEL MOUNTING

4. CONNECTIONS

Insert probes 2 and 3 (17-18-19) are disabled at the factory.
Relay outputs 9-10 (oA3)=light, 7-8 (oA1)=Aux, 1-2(oA2)=alarm are configured at the factory.
Port micro connects to contacts 25-26.

«
...
3
4
5
6
7
...
»

Содержание XB590L

































Отзывы:

Нет отзывов

Похожие инструкции для XB590L

OMNI OWC-5 Series

Бренд: Enviroheat Страницы: 70

Бренд: Crommelins Страницы: 19

AquaForce 30XQ0330

Бренд: Carrier Страницы: 49

Бренд: York Страницы: 24

Бренд: AL-KO Страницы: 53

Бренд: York Страницы: 104

CWW 18/C Series

Бренд: Clint Страницы: 10

Бренд: Daikin Страницы: 97

Pro-Dialog Plus 30SZ

Бренд: Carrier Страницы: 24

Бренд: D-D The Aquarium Solution Страницы: 11

Бренд: Hansa Страницы: 22

Бренд: AERMEC Страницы: 56

Бренд: Johnson Controls Страницы: 38

BIO MASTER 2200

Бренд: Stiga Страницы: 148

Бренд: Trane Страницы: 24

Бренд: Texas Equipment Страницы: 18

Бренд: Texas Equipment Страницы: 26

Бренд: Texas Equipment Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды