DIVEX MHE-02, Инструкция по установке, эксплуатации и обслуживанию

Страница: 72 / 119

IMCB34-E1
5
4. PARTS DESCRIPTION
(1)
CB100
CB100
PV
SV
AT
R/S SET
OUT1 OUT2 ALM1 ALM2
(2)
(3)
(4) (5) (6) (7)
AT OUT1
R/S
PV
SET
CB500
SV
OUT2 ALM1 ALM2
(2)
CB500
(1)
(3)
(4) (5) (6) (7)
PV
SV
AT OUT1
ALM1 ALM2
OUT2
CB400
R/S
SET
(1)
(3)
(4) (5) (6) (7)
CB400
(2)
PV
SV
AT OUT1
R/S
SET
OUT2 ALM1 ALM2
CB900
(1)
(3)
(2)
(4) (5) (6) (7)
CB700, CB900
5. SETTING
5.1 Operation Menu
Display returns to the PV/SV display
mode if no key operation is performed
within 1 minute.
Input type and input range display
This instrument immediately confirms the input type symbol and input range following power ON.
Example: When sensor type of input is K thermocouple.
(1) Measured value (PV) display [Green]
Displays PV or various parameter symbols.
(2) Set value (SV) display [Orange]
Displays SV or various parameter set values (or
CT input value).
(3) Indication lamps
Alarm output lamps (ALM1, ALM2) [Red]
ALM1: Lights when alarm 1 output is turned on.
ALM2: Lights when alarm 2 output is turned on.
Autotuning (AT) lamp [Green]
Flashes when autotuning is activated. (After
autotuning is completed: AT lamp will go out)
Control output lamps (OUT1, OUT2) [Green]
OUT1: Lights when control output is turned on.*
OUT2: Lights when cool-side control output is
turned on.*
* Lamp indication becomes as follows for
current output.
For an output of less than 0 %: Extinguished
For an output of more than 100 %: Lit
For an output of more than 0 % but less than
100 %: Dimly lit.
(4) (Set key)
Used for parameter calling up and set value
registration.
SET
(5) (Shift & R/S key)
Shift digits when settings are changed.
Select the RUN/STOP function.
(6) (DOWN key)
Decrease numerals.
(7) (UP key)
Increase numerals.
R /S
To avoid damage to the
instrument, never use a
sharp object to press keys.
Symbol
PV
SV
PV
SV
Unit for input and SV display
(Celsius: C, Fahrenheit: F, Voltage/Current input: no character shown)
Input type symbol *
Input range high
Input range low
Automatically
Power ON
PV/SV Display Mode
The controller will display the Measured
value (PV) and the Set value (SV).
The controller can be switched to RUN or
STOP mode (Factory set value: RUN).
PV/SV monitor
(RUN mode) PV
SV
Press and hold the <R/S key
for 1 second.
SV
STOP character display
(STOP mode)
SV Setting Mode
SV setting
PV
SV
This is the mode used to set the SV.
Factory set value: 0 C [ F] or 0.0 C [ F]
Press the SET key
Press and hold
the SET key
for 2 seconds.
Press
the <R/S key
while
pressing the
SET key.
Input type and Input range Display
Automatically (in 4 seconds)
Parameter Setting Mode
This mode is used to set the parameters such as alarms, PID constants, etc. (Refer to page 6 .)
The following parameter symbols are displayed as the SET key is pressed.
SET key
Current transformer
(CT) input value 1
monitor
Control loop break
alarm (LBA) time
LBA deadband
Alarm 1 set value
(ALM1)
Alarm 2 set value
(ALM2)
Heater break alarm
(HBA) 1 set value
Autotuning (AT)
Self-tuning (ST)
Proportional band
Integral time
Derivative time
Anti-reset windup
Heat-side proportioning
cycle
Cool-side proportioning
band
Deadband
Cool-side proportioning
cycle
PV bias
Set data lock
Return to the first parameter
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
SET key
Parameters which are not related to existing functions on the controller are not displayed.
(CT1)
(AL1)
(AL2)
(HbA1)
(LbA)
(Lbd)
(ATU)
(STU)
(P)
(I)
(D)
(Ar)
(T)
(Pc)
(db)
(t)
(Pb)
(LCK)
Communication Setting Mode
This mode is used to set the communication parameters when specified. For details on protocol, identifiers
and communication setting mode, refer to the
Communication Instruction Manual (IMCB03-E ) .
P = 0 (0.0):
ON/OFF action
( ): This input type is not displayed in the Z-1021 specification.
* Input Type Symbol Table
Symbol
Thermocouple (TC)
W5Re/
W26Re
U L
Voltage
(Current)
JPt
100
Pt
100
K J R S B E T N
( )
Input type
RTD
( )
PL II