background image

SK5TR

 Attachment Operator’s Manual

Publication number: 054-096; page 7 of 9

Check Trencher Headshaft Sprocket Bolts

Check tightness of 
headshaft sprocket 
bolts as needed. 
Tighten lubricated 
bolts to 85 ft•lb (115 
N•m)

Replace Digging Chain

To remove digging chain:

1.

Start engine.

2.

Position digging chain with connector pin at top of 
boom.

3.

Lower boom to ground.

4.

Stop engine.

5.

Secure chain.

With sprocket booms, 
lock rear idler 
sprocket.

With roller booms, 
clamp links on either 
side of connector pin 
with chain jaws 
(shown). Squeeze 
jaws to reduce 
pressure on connector 
pin.

6.

Loop cable through links 
nearest connector pin 
(shown). 

7.

Turn tension bolts 
counterclockwise to 
release tension on digging 
chain.

8.

Stand clear of chain. Do 
not stand behind boom. 
Keep feet from under boom.

9.

Remove pin from connector pin and drive pin out of 
link.

10. Unclamp links (roller boom). Slowly release cable 

and lower chain to ground.

To install digging chain:

1.

Position digging chain on ground with teeth down 
and pointed toward unit. 

2.

Loop cable through end links.

3.

Start engine.

4.

Back unit up until digging chain extends past 
headshaft about 12” (30 cm).

5.

Lower boom to horizontal position.

6.

Stop engine.

7.

Secure chain on sprocket booms by locking rear idler 
sprocket.

8.

Pull rear end of chain over tail sprocket or roller. Pull 
cable until chain is in place on boom.

9.

Attach chain jaws to end links and bring links into 
place.

10. Install connector pin and lock key.

t05om060c

.

eps

Содержание SK5TR










Отзывы: