Distech Controls EC-BOS-6AX Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

background image

Replacement Parts

Non-replaceable Parts

EC-BOS-6

AX

Mounting and Wiring Instructions

Part Number: 05DI-HIBS6AX-10

Revised: February 2008

21

Procedure 5

Replacing NiMH battery assembly on an EC-BOS-6

AX

.

Step 1

Backup the EC-BOS-6

AX

controller’s configuration to your PC using the appropriate NiagaraAX

software tool (for example, EC-Net

AX

Pro).

Step 2

Remove power from the EC-BOS-6

AX

.

Wait for LED activity to stop - after several seconds, all LEDs on the EC-BOS-6

AX

should be off.

Step 3

Remove the cover. See

“Removing and Replacing the Cover,”

Step 4

Remove the old battery and bracket assembly by taking out the four screws holding it in place, setting
the screws aside for later. Unplug the battery from the connector on the EC-BOS-6

AX

.

Step 5

Plug the battery connector plug of the

replacement battery

into the battery connector on the

EC-BOS-6

AX

.

Step 6

Set the replacement battery/bracket assembly back over the option card slots, with the mounting holes
aligned with the standoffs.

Step 7

Place the four screws through the battery bracket, option cards blanking plates, and into the standoffs
on the EC-BOS-6

AX

base board. Hand tighten these screws.

Step 8

Replace the cover.

Step 9

Restore power to the EC-BOS-6

AX

and verify normal operation.

Replacement Parts

Servicing the EC-BOS-6

AX

may call for replacement parts. There are three categories of parts:

•

Non-replaceable Parts

•

Standard Replacement Parts

•

New Replacement Units

Non-replaceable Parts

Other than the parts listed in the replacement parts sections, there are no serviceable components on the base
assembly.

Memory

Any addition, modification, or replacement of memory components requires software configuration and is not
a field upgrade. For additional information on modifying the memory capacity of the EC-BOS-6

AX

, consult

Distech Controls office for technical support

Fuse

The EC-BOS-6

AX

contains a non-user replaceable fuse, soldered on the circuit board. This fuse provides

protection from internal shorts or connection to incorrect power supplies. If the fuse circuitry is suspect, contact
Distech Controls office for technical support. See the

“Federal Communications Commission (FCC)”

«
...
19
20
21
22
23
...
»

Содержание EC-BOS-6AX





























Отзывы:

Нет отзывов

Похожие инструкции для EC-BOS-6AX

Бренд: KELCO Страницы: 36

Бренд: Accel Страницы: 8

Бренд: EasyIO Страницы: 18

Бренд: Easylift Страницы: 127

Бренд: Harmonic Drive Страницы: 85

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 98

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 54

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды