Dish Network 1000.4 Dish Скачать руководство пользователя страница 8

Страница: 8 / 18

Dish Antennas - DISH 1000.4

2 - 8

DISH 1000.4 (continued)
Installation Considerations

•

All receivers must have MPEG-4 support (ViP-series receivers).

•

Provides additional peaking controls for easier installation and peaking.

–

Azimuth Cam provides fine-tuning of the azimuth angle.

–

Elevation Rod provides fine-tuning of the elevation angle and additional installation stability.

•

Nuts and bolts on the dish should be tightened using a torque wrench in a specific order. Follow the manufacturer’s
instructions for the correct order.

•

When tightening the azimuth bolts, do not tighten the Azimuth Cam.

•

After peaking on 72.7°, confirm signal on 61.5° and 77°.

•

The 1000.4 dish antenna uses the same mast and foot as the DISH 500+.

•

Mast clamp includes a gripping feature that provides additional installation stability.

•

LNBF Arm has a specific installation orientation, indicated by labeling “Top” and “To LNBF”.

•

Antenna dimensions: 27.8”W x 22.3”H.

Содержание 1000.4 Dish



















Результаты поиска

Содержание 1000.4 Dish

Отзывы:

Похожие инструкции для 1000.4 Dish

Бренды по названию

Популярные бренды

Dish Network 1000.4 Dish, Руководство пользователя

Результаты поиска

Содержание 1000.4 Dish

Отзывы:

Похожие инструкции для 1000.4 Dish

Бренды по названию

Популярные бренды