background image

55

EN

EWS3 – Wireless Indoor Siren

6.  Close EWS3 enclosure by putting the cover back (see Fig. No. 3).

7.  Bind the device to the alarm system using 

ELDES Configuration Tool

 software. Open

 Wireless Device Management

 section and 

enter a 8-digit wireless device ID located on the EWS3 enclosure and press 

Add

 button (see Fig. No.10). The device can also be bind by 

sending a corresponding command via SMS message. For more details, please refer to the software‘s HELP section and ELDES alarm 

system installation manual.

 

10

8.  Upon the successful binding process, EWS3 device icon becomes visible in 

Wireless Device Management

 section as well as 

Battery 

Level

 and 

Signal Level

. If attempt to bind is unsuccessful, try to move EWS3 closer to the alarm system device and bind anew.

9.  EWS3 siren is ready for use.

ATTENTION: 

  

Ensure that EWS3 device is properly fixed to the wall and the Mounting Point A portrayed in Fig. No. 4 and Fig. No. 5 is properly 

screwed in. Otherwise, the tamper switch will NOT supervise the back side of EWS3 enclosure (see also 

4. EWS3 ZONE, PGM OUTPUT 

AND TAMPER

). 

NOTE: 

  

If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again. 

See chapter 

6. RESTORING DEFAULT PARAMETERS

 for more details.

Содержание EWS3








Отзывы: