1. Press the down arrow until you see “9. Image” then press the ‘ENT’ button
you should see “9-01. Image P: A Load” Press the down arrow to display “9-
02. Image P: A Delete Image”
2. Press the ‘ENT’ button and “Delete Image in Partition A?Yes” will display in
the LCD window. Pressing the ‘ENT’ button will delete the image in the A par-
tition. The message will show “Partition : A Image is deleted” Press the ‘ESC’
key to return to the Image submenu.
9.03 Image Info:
use this sub-function to show the number of sessions and
tracks on the currently selected partition of the hard drive.
1. Press the down arrow until you see “9. Image” then press the ‘ENT’ button
you should see “9-01. Image P: A Load” Press the down arrow to display “9-
03. Image P: A Image info”
2. Press the ‘ENT’ key and the number of sessions and tracks will be displayed,
pressing the up and down arrow will display total time of the image, total MB
of the image, and the tracks and the track size. Note: data tracks will not dis-
play and time length.
9.04 Compare Image:
use this sub-function to compare the image to a CD in
the source recorder for the hard drive.
1. Press the down arrow until you see “9. Image” then press the ‘ENT’ button,
you should see “9-01. Image P: A Load”, press the down arrow to display “9-
04. Image P: A Compare Image”.
2. Load the top drive (source recorder for the hard drive) with the disc to be
compared and press the ‘ENT’ button. When the process is finished the
same screens will be displayed as in the full function (5. Compare) but the
disc will not be ejected.
9.05 Select Image:
use this sub-function to select which partition on the hard
drive will be used.
1. Press the down arrow until you see “9. Image” then press the ‘ENT’ button
you should see “9-01. Image P: A Load”, press the down arrow to display “9-
05. Image P: A Select Image”.
2. Press the ‘ENT’ key and the LCD will display “Select Working Partition - A”.
Pressing the up and down arrows will cycle through the partitions on
the hard drive. At the desired partition press the ‘ENT’ key and “Set
Partition to ...” will be displayed to confirm that the partition is selected.
The ReflexPro unit is equipped with an eighty GB hard drive. Each partition is
approximately 1 GB. The partitions are arranged alphabetically, A through Z,
AA through AZ, and BA through BW
9.06 Image Source Drive:
use this sub-function to select which recorder is
used as the source reading a CD to the hard drive. The ReflexPro is defaulted to
use the top recorder drive in the unit.
1. Press the down arrow until you see “9. Image” then press the ‘ENT’ button
you should see “9-01. Image P: A Load”, press the down arrow to display “9-
06. Image P: A Image Src Drive”.
2. Press the ‘ENT’ key and the LCD will display “Select Img Src: 01 IDE1 CD-RW
N”. Pressing the up and down arrows will cycle through the recorder drive
from 01 at the top to 04 at the bottom, 07 on ReflexPro7. At the desired drive
press the ‘ENT’ key and “Load image from Drive ID - 0...” will be displayed to
confirm the change in source recorder.
10. E
DIT
T
RACK
The ReflexPro can be used to create custom audio CDs. This function allows the
user to take audio tracks from different CDs and compile them to a single CD.
This function is only available in the disc to disc mode.
1. Set the ReflexPro to disc to disc mode (see page 9), then select the “Edit
Track” function using the up and down arrows.
2. Load the top drive (Src) with the master disc. Press the “ENT” button once to
see the main screen for this function, “10-01 Edit Track CD to CD Edit.” Press
the ENT button again to see the following screen:
1-800-237-6666
www.discmakers.com
T
10
Select Track:
1/31
2:41
